HPE Aruba Networking 650 Series Wi-Fi 6E APs

Deliver the highest levels of performance with Wi-Fi 6E—greater capacity, wider channels, and less interference.

Meet HPE Aruba Networking’s flagship Wi-Fi 6E access point

With up to 1200 MHz of new channels, capacity is nearly tripled—so you can meet growing demands due to bandwidth-hungry video, increasing numbers of client and IoT devices, and growth in cloud.

Greater capacity with 6GHz

Greater capacity with 6GHz

The 650 Series APs are indoor access points that are fully equipped to support the 6 GHz band for faster performance, wider channels, and minimal interference. Our flagship campus Wi-Fi 6E APs deliver 7.8 Gbps maximum aggregate data rates and 4x4 MU-MIMO.

Maximize channel utilization

Maximize channel utilization

HPE Aruba Networking’s patented ultra tri-band filtering allows organizations to take full advantage of 6GHz unlicensed spectrum by dynamically adjusting the available channels to eliminate signal interference and performance degradation.

Highly efficient and secure

Highly efficient and secure

Wi-Fi 6E extends the  802.11ax standard to the 6GHz band. All the efficiency and security enhancements including orthogonal frequency-division multiple access (OFDMA), Multi-User MIMO, Enhanced Open, and WPA3 are supported. 

IoT ready

IoT ready

Integrated Bluetooth Low Energy (BLE) and Zigbee support make it easier to deploy and manage IoT, including asset tracking, security solutions, and sensors.

Wi-Fi 6E for your most demanding environments

HPE Aruba Networking 650 Series APs take advantage of the 6 GHz band for fast, secure connectivity plus configurable 5 Gbps dual Ethernet ports for high availability.

Highly resilient

Provide hitless failover for data and power with two configurable HPE ® Smart Rate ethernet ports that can support 1, 2.5, or 5 Gbps.

Secure connectivity

Supports WPA3 and Enhanced Open as part of the Wi-Fi 6E standard for stronger guest access and data encryption.

Automatic role-based access enforcement

Centrally configure and automatically enforce role-based policies across wired and wireless networks.

Dynamic traffic steering

Load balance traffic for better performance by automatically steering traffic from the 2.4 GHz band to the preferred 5 GHz or 6 GHz band.

Details and specifications for the HPE Aruba Networking 650 Series APs

Details and specifications for the HPE Aruba Networking 650 Series APs
  • Hardware variants
    • AP-654: External antenna models
    • AP-655: Internal antenna models
    Wi-Fi radio specifications
    • AP type: Indoor, tri-radio, 2.4GHz, 5GHz and 6GHz (concurrent) 802.11ax 4x4 MIMO
    • 2.4GHz radio: Four spatial streams MIMO for up to 1,147Mbps wireless data rate with HE40 802.11ax client devices
    • 5GHz radio: Four spatial streams MIMO for up to 2.4Gbps wireless data rate with HE80 802.11ax client devices
    • 6GHz radio: Four spatial streams MIMO for up to 4.8Gbps wireless data rate with HE160 802.11ax client devices
    • Both downlink and uplink MU-MIMO in 6GHz and 5GHz, downlink only in 2.4GHz
    • Up to 512 associated client devices per radio, and up to 16 BSSIDs per radio (limited to 4 for the 6GHz radio)
    • Supported frequency bands (country-specific restrictions apply):
      • 2.400 to 2.4835GHz ISM
      • 5.150 to 5.250GHz U-NII-1
      • 5.250 to 5.350GHz U-NII-2A
      • 5.470 to 5.725GHz U-NII-2C
      • 5.725 to 5.850GHz U-NII-3/ISM
      • 5.850 to 5.895GHz U-NII-4
      • 5.925 to 6.425GHz U-NII-5
      • 6.425 to 6.525GHz U-NII-6
      • 6.525 to 6.875GHz U-NII-7
      • 6.875 to 7.125GHz U-NII-8
    • Available bands and channels: Dependent on configured regulatory domain (country)
    • Dynamic frequency selection (DFS) optimizes the use of available RF spectrum in the 5GHz band
      • Including Zero-Wait DFS (ZWDFS) to accelerate channel changes
    • Supported radio technologies:
      • 802.11b: Direct-sequence spread-spectrum (DSSS)
      • 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
      • 802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 37 resource units (for an 80MHz channel)
    • Supported modulation types:
      • 802.11b: BPSK, QPSK, CCK
      • 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM and 256-QAM (proprietary extension)
      • 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM and 1024-QAM (proprietary extension)
      • 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM and 1024-QAM
    • 802.11n high-throughput (HT) support: HT20/40
    • 802.11ac very high throughput (VHT) support: VHT20/40/80/160(80+80)
    • 802.11ax high efficiency (HE) support: HE20/40/80/160
    • Supported data rates (Mbps):
      • 802.11b: 1, 2, 5.5, 11
      • 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
      • 802.11n: 6.5 to 600 (MCS0 to MCS31, HT20 to HT40), 800 with 256-QAM (proprietary extension)
      • 802.11ac: 6.5 to 1,733 (MCS0 to MCS9, NSS = 1 to 4, VHT20 to VHT160(80+80));VHT80); 2,167 with 1024-QAM (MCS10 and MCS11, proprietary extension)
      • 802.11ax (2.4GHz): 3.6 to 1,147 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE40)
      • 802.11ax (5GHz): 3.6 to 2,402 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE160(80+80))HE80)
      • 802.11ax (6GHz): 3.6 to 4,804 (MCS0 to MCS11, NSS = 1 to 4,HE20 to HE160)
    • 802.11n/ac packet aggregation: A-MPDU, A-MSDU
    • Transmit power: Configurable in increments of 0.5 dBm
    • Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):
      • Per radio/band (2.4GHz / 5GHz / 6GHz): +24 dBm (18dBm per chain)
      • Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain.
    • Advanced Cellular Coexistence (ACC) minimizes the impact of interference from cellular networks
    • Ultra Tri-Band (UTB) enables ultimate flexibility in 5GHz and 6GHz channel selection without performance degradation
    • Maximum ratio combining (MRC) for improved receiver performance
    • Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
    • Space-time block coding (STBC) for increased range and improved reception
    • Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
    • Transmit beam-forming (TxBF) for increased signal reliability and range
    • 802.11ax Target Wait Time (TWT) to support low-power client devices
    Wi-Fi antennas
    • AP-654: Two sets of four (female) RP-SMA connectors for external antennas (A0 through A3 corresponding with radio chains 0 through 3 for the 2.4GHz and 5GHz radios, and B0 through B3 corresponding with radio chains 0 through 3 for the 6GHz radio). Worst-case internal loss between radio interface and external antenna connectors: 1.0dB in 2.4GHz, 1.0dB in 5GHz and 1.0dB in 6GHz.
    • AP-655: Integrated downtilt omni-directional antennas for 4x4 MIMO with peak antenna gain of 4.8dBi in 2.4GHz, 5.3dBi in 5GHz and 5.4dBi in 6GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 to 40 degrees.
      • Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the combined, average pattern is 3.3dBi in 2.4GHz, 2.9dBi in 5GHz and 4.0dBi in 6GHz.
    Other interfaces
    • E0, E1: Two Ethernet wired network ports (RJ-45)
      • Auto-sensing link speed (100/1000/2500/5000BASE-T) and MDI/MDX
      • 2.5Gbps and 5Gbps speeds comply with NBase-T and 802.3bz specifications
      • POE-PD: 48Vdc (nominal) 802.3af/at/bt POE (class 3 or higher)
      • 802.3az Energy Efficient Ethernet (EEE)
      • Link aggregation (LACP) support between both network ports for redundancy and increased capacity
    • DC power interface: 48Vdc (nominal, +/- 5%), accepts 1.35mm/3.5mm center-positive circular plug with 9.5mm length
    • USB 2.0 host interface (Type A connector)
      • Capable of sourcing up to 1A / 5W to an attached device
    • Bluetooth Low Energy (BLE5.0) and Zigbee (802.15.4) radio
      • BLE: up to 6dBm transmit power and -101dBm receive sensitivity (125kbps)
      • Zigbee: up to 6dBm transmit power and -97dBm receive sensitivity (250kbps)
      • Integrated omnidirectional antenna with roughly 30 to 40 degrees downtilt and peak gain of 3.5dBi
    • Advanced IOT Coexistence (AIC) allows concurrent operation of multiple radios in the 2.4GHz band
    • Built-in Trusted Platform Module (TPM) for enhanced security and anti-counterfeiting
    • Visual indictors (four multi-color LEDs): for System (1x) and Radio (3x) status
    • Reset button: factory reset, LED mode control (normal/off)
    • Serial console interface (proprietary, micro-B USB physical jack)
    • Kensington security slot
    • Automatic thermal shutdown and recovery function
  • Power sources and power consumption
    • The AP supports direct DC power and Power over Ethernet (POE) on port E0 and/or E1
    • When POE power is supplied to both Ethernet ports, the AP combines power from both sources (SmartPOE feature), using E0 as the primary source and E1 as secondary
    • When both DC and POE power sources are available, DC power takes priority over POE
    • Power sources are sold separately; see the 650 Series Ordering Guide for details
    • The AP supports various power modes depending on the available power source(s) and configuration
      • With IPM disabled, the AP may apply some static restrictions, see tables below
      • With IPM enabled, the AP will start up in unrestricted mode but may dynamically apply restrictions depending on the available power budget and actual consumption. The feature restrictions and order in which these get applied are configurable
      • When powered by direct DC power, the AP operates without restrictions
      • Powering the AP from a single 802.3af (class 3 or lower) POE source is not supported (except for AP staging), regardless of IPM status
    • Maximum (worst-case) power consumption (without / with a USB device attached):
      • DC powered: 36.0W / 42.5W
      • POE powered: 40.3W / 46.5W
      • This assumes that up to 5W is supplied to the attached USB device
    • Maximum (worst-case) power consumption in idle mode: 14.3W/20.2W (DC) or 16.9W/22.7W (POE)
    • Maximum (worst-case) power consumption in deep-sleep mode: 2.4W (DC) or 4.0W (POE)
    Mounting details
    • A mounting bracket has been pre-installed on the back of the AP. This bracket is used to secure the AP to any of the mount kits (sold separately); see the 650 Series Ordering Guide for details.
    Mechanical specifications
    • Dimensions/weight (AP-655; unit without mount bracket):
      • 260mm (W) x 260mm (D) x 60mm (H)
      • 1,800g
    • Dimensions/weight (AP-655; shipping):
      • 285mm (W) x 285mm (D) x 95mm (H)
      • 2,300g
    Environmental specifications
    • Operating conditions
      • Temperature: 0°C to +50°C / +32°F to +122°F
      • Relative humidity: 5% to 95%
      • ETS 300 019 class 3.2 environments
      • AP is plenum rated for use in air-handling spaces
    • Storage conditions
      • Temperature: -25°C to +55°C / -13°F to +131°F
      • Relative humidity: 10% to 100%
      • ETS 300 019 class 1.2 environments
    • Transportation conditions
      • Temperature: -40°C to +70°C / -40°F to +158°F
      • Relative humidity: up to 95%
      • ETS 300 019 class 2.3 environments
    Reliability
    • Mean Time Between Failure (MTBF): 544khrs (62yrs) at +25°C operating temperature
    Regulatory compliance
    • FCC/ISED
    • CE Marked
    • RED Directive 2014/53/EU
    • EMC Directive 2014/30/EU
    • Low Voltage Directive 2014/35/EU
    • UL/IEC/EN 60950
    • IEC/EN 62368-1
    • EN 60601-1-1, EN60601-1-2
    • For more country-specific regulatory information and approvals, please see your HPE Aruba Networking representative.
    • Regulatory considerations for AP-654:
      • The AP-654 will be offered in countries where there is an existing or clear and defined path to allow operation of 6 GHz radios with external connectorized antennas, either as a Low Power Indoor (LPI) or Standard Power (SPI) product. Please contact your HPE Aruba Networking representative to confirm (existing or planned) availability for the country where the AP will be deployed.
    Regulatory model numbers
    • AP-654 (all models): APIN0654
    • AP-655 (all models): APIN0655
    Certifications
    • UL2043 plenum rating
    • Wi-Fi Alliance (WFA):
      • Wi-Fi CERTIFIED a, b, g, n, ac
      • Wi-Fi CERTIFIED 6E (ax, 6GHz)
      • WPA, WPA2 and WPA3 – Enterprise with CNSA option, Personal (SAE), Enhanced Open (OWE)
      • WMM, WMM-PS, W-Fi Agile Multiband
      • Wi-Fi Location*
      • Passpoint (release 2)
    • Bluetooth SIG
    • Ethernet Alliance (POE, PD device, class 6)

    *Targeting Q2 CY22 to obtain the Wi-Fi Location certification

    Warranty
    Minimum operating system software versions
    • AP-654 (excluding 6GHz support):
      • ArubaOS and Aruba InstantOS 8.11.2.0, ArubaOS 10.6.0.0
    • AP-654 (including 6GHz support):
      • ArubaOS and Aruba InstantOS 8.12.0.0, ArubaOS 10.7.0.0
    • AP-655:
      • ArubaOS and Aruba InstantOS 8.10.0.1, ArubaOS 10.4.0.0

Related products

Find information on HPE Aruba Networking products that complement the 650 Series Wi-Fi 6E APs or another solution that might better suit your needs.

630 Series Wi-Fi 6E APs

High-capacity Wi-Fi 6E campus access points with 3.9 Gbps maximum aggregate throughput, now Wi-Fi Alliance certified.

610 Series Wi-Fi 6E APs

Compact, affordable Wi-Fi 6E access point features a configurable dual radio, tri-band architecture that can dynamically adjust to use any two of the three Wi-Fi 6E bands (2.4 GHz, 5 GHz, and 6 GHz).

Aruba 550 series access points

550 Series Wi-Fi 6 APs

Flagship Wi-Fi 6 campus access points with support for 8x8 or dual 4x4 5 GHz radios.

Ready to get started?