HPE Aruba Networking 670 Series Outdoor Access Points

HPE Aruba Networking 670 Series Outdoor Access Points are high-performance Wi-Fi 6E APs ideal for outdoor and environmentally challenging locations.

Wi-Fi 6E for extreme outdoor conditions

Provide secure and reliable connectivity in large outdoor open areas, such as stadiums and public venues with weatherproof high-performance Wi-Fi 6E APs.

Wi-Fi 6E performance

Wi-Fi 6E performance

Improve Wi-Fi performance using the 6 GHz band for faster speeds and wider channels. Tri-band coverage across 2.4 GHz, 5 GHz, and 6 GHz delivers 3.9 Gbps maximum aggregate data rate supports high-bandwidth, low-latency applications such as high-definition video.

Ruggedized for outdoors

Ruggedized for outdoors

Withstand extreme high and low temperatures, persistent moisture, and precipitation. Fully sealed to keep out airborne contaminants and electrical interfaces including industrial-strength surge protection. Available with choice of internal antenna (omni, directional, or point-to-point) to optimize wireless coverage.

IoT ready

IoT ready

Deploy and manage enterprise and industrial IoT, including asset tracking services, security solutions, and sensors, with integrated high-power Bluetooth and 802.15.4 radios for Zigbee support. Advanced IoT Coexistence (AIC) helps Wi-Fi, Bluetooth and Zigbee radios operate at maximum capacity without interference.

Location aware

Location aware

Protect incumbent outdoor services via self-locating embedded GPS receivers that operate as Standard Power (SP) devices, requiring an Automated Frequency Coordination service (AFC).

Efficient and secure

Efficient and secure

Extend the 802.11ax standard to the 6GHz band, including efficiency and security enhancements such as orthogonal frequency-division multiple access (OFDMA), multi-user MIMO, enhanced open, and WPA3 with Wi-Fi 6E. The 670 Series APs also offers client optimization, automated radio frequency management, and intelligent power monitoring.

Wi-Fi 6E for the extreme outdoors

High-performance Wi-Fi 6E for reliable and secure connectivity across the most demanding outdoor environments, including public venues.

6 GHz support

Tri-band coverage across 2.4 GHz, 5 GHz, and 6 GHz to deliver 3.9 Gbps maximum combined peak data rate.

Standard power (SP) device operations

Self-locating with embedded GPS receivers that can operate as a standard power (SP) device pending per country certification and approval.

IP66/67 rated for challenging conditions

Purpose built to survive in the harshest outdoor environments and extreme temperatures (-40 to +70˚C).

Multi-gigabit ethernet speeds

Flexible and fast wired connectivity with 2.5GbE port and 1GbE SFP port.

High-power Bluetooth and Zigbee radios

Simplified deployment and management of IoT devices for industrial IoT and manufacturing environments.

Built-in security

Includes Wi-Fi 6E standards such as WPA3, enhanced open, and WPA2-MPSK for stronger encryption and authentication.

Details and specifications for the HPE Aruba Networking 670 Series Outdoor APs

Details and specifications for the HPE Aruba Networking 670 Series Outdoor APs
  • Hardware variants
    • HPE Aruba Networking AP-675
      • Built in omnidirectional antennas
      • 2.4 GHz antennas 3.5dBi
      • 5 GHz antennas 5dBi
      • 6 GHz antennas 5dBi
      • BLE/Zigbee: Integrated omnidirectional antenna with peak gain of 6dBi
    • HPE Aruba Networking AP-677
      • Built in directional antennas
      • 2.4 GHz antennas 5.6dBi
      • 5 GHz antennas 6dBi
      • 6 GHz antennas 7dBi
      • BLE/Zigbee: Integrated omnidirectional antenna with peak gain of 8dBi
    • HPE Aruba Networking AP-679
      • Built in dynamic directional antennas
      • 2.4 GHz antennas 6dBi
      • 5 GHz antennas
        • Wide 9dBi
        • Narrow 12dBi
      • 6 GHz antennas
        • Wide 9dBi
        • Narrow 13dBi
      • BLE/Zigbee: Integrated omnidirectional antenna with peak gain of 6dBi
    Wi-Fi radio specifications
    • AP type: Outdoor, tri radio, 2.4GHz, 5GHz and 6GHz (concurrent) 802.11ax 2x2 MIMO
    • 2.4 GHz radio: Two spatial stream single user (SU) MIMO for up to 574 Mbps wireless data rate with 2SS HE40 802.11ax client devices
    • 5 GHz radio: Two spatial stream single user (SU) MIMO for up to 1.2 Gbps wireless data rate with 2SS HE80 802.11ax client devices
    • 6 GHz radio: Two spatial stream single user (SU) MIMO for up to 2.4 Gbps wireless data rate with 2SS HE160 802.11ax client devices
    • Up to 512 associated client devices per radio, and up to 16 BSSIDs per radio (limited to 8 for the 6GHz radio)
    • Supported frequency bands (country-specific restrictions apply):
      • 2.400 to 2.4835 GHz ISM
      • 5.150 to 5.250 GHz U-NII-1
      • 5.250 to 5.350 GHz U-NII-2
      • 5.470 to 5.725 GHz U-NII-2E
      • 5.725 to 5.850 GHz U-NII-3/ISM
      • 5.850 to 5.895 GHz U-NII-4
      • 5.925 to 6.425 GHz U-NII-5
      • 6.425 to 6.525 GHz U-NII-6
      • 6.525 to 6.875 GHz U-NII-7
      • 6.875 to 7.125 GHz U-NII-8
    • Available bands and channels: Dependent on configured regulatory domain (country)
    • Dynamic frequency selection (DFS) optimizes the use of available RF spectrum in the 5 GHz band
    • Supported radio technologies:
    • 802.11b: Direct-sequence spread-spectrum (DSSS)
    • 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
    • 802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 8 resource units (37 for the 6GHz radio)
    • Supported Modulation Types
      • 802.11b: BPSK, QPSK, CCK
      • 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM and 256-QAM (proprietary extension)
      • 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM and 1024-QAM (proprietary extension)
      • 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, and 1024-QAM
    • 802.11n high-throughput (HT) support: HT20/40
    • 802.11ac very high throughput (VHT) support: VHT20/40/80
    • 802.11ax high efficiency (HE) support: HE20/40/80/160
    • Supported data rates (Mbps):
      • 802.11b: 1, 2, 5.5, 11
      • 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
      • 802.11n: 6.5 to 300 (MCS0 to MCS15, HT20 to HT40), 400 with 256-QAM (proprietary extension)
      • 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2, VHT20 to VHT80); 1,083 with 1024-QAM (MCS10 and MCS11, proprietary extension)
      • 802.11ax (2.4GHz): 3.6 to 574 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE40)
      • 802.11ax (5GHz): 3.6 to 1,201 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE80)
      • 802.11ax (6GHz): 3.6 to 2,402 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE160)
    • 802.11n/ac packet aggregation: A-MPDU, A-MSDU
    • Transmit power: Configurable in increments of 0.5 dBm
    • Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements)
      • Per radio/band (2.4 GHz/5 GHz/6 GHz): +25 dBm (18 dBm per chain)
      • Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain.
    • Advanced cellular coexistence (ACC) minimizes the impact of interference from cellular networks
    • Maximum ratio combining (MRC) for improved receiver performance
    • Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
    • Space-time block coding (STBC) for increased range and improved reception
    • Low-density parity check (LDPC) for high- efficiency error correction and increased throughput
    • Transmit beamforming (TxBF) for increased signal reliability and range
    • 802.11ax Target Wait Time (TWT) to support low-power client devices
    • 802.11mc Fine Timing Measurement (FTM) for precision distance ranging
    Power
    • The AP supports power over ethernet (PoE) on port E0
    • Power sources are sold separately; see the HPE Aruba Networking 67 Series ordering guide for details
    • When powered by 802.3bt (class 6) PoE, the AP will operate without restrictions.
    • When powered by 802.3bt (class 5) PoE with the IPM feature disabled, the AP will disable the USB-C port.
    • Operating the AP with an 802.3at (class 4) POE with the IPM feature disabled, the AP will disable the USB ports, the SFP port, and one of the two chains on the 2.4Ghz radio
    • Operating the AP with an 802.3af (class 3 or lower) POE source is not supported (except for AP staging)
    • With IPM enabled, the AP will start up in unrestricted mode but may dynamically apply restrictions depending on the available power budget and actual consumption. The feature restrictions and order in which these get applied are configurable.
    • Maximum (worst-case) power consumption (without/with a USB device attached):
      • PoE powered: 29W/45.5W.
      • This assumes that up to 16.5W total is supplied the attached USB devices
    • Maximum (worst-case) power consumption in idle mode: 11W/27.5W (both USB active at max).
    • Maximum (worst-case) power consumption in deep-sleep mode: 3.2W (PoE).
  • Additional Interfaces
    • Wired network interface (E0)
      • Auto-sensing link speed (100/1000/2500BASE-T) and MDI/MDX
      • 2.5 Gbps speed complies with NBase-T and 802.3bz specifications
      • PoE-PD: 48Vdc (nominal) 802.3at/bt PoE (class 4 or higher)
      • 802.3az Energy Efficient Ethernet (EEE)
    • Wired network interface (E1)
      • SFP Fiber Port
      • When used in operation it is expected that this is the primary uplink port
      • -Only recommended industrial temperature SFP/SFP+ modules should be used for optimal performance
    • USB 3.0 host interface (type C connector), supporting 2A/10W maximum
    • USB 2.0 host interface (type A connector), supporting 1A/5W maximum
    • Bluetooth low energy (BLE5.0) and Zigbee (802.15.4) radio
    • BLE: up to 8 dBm transmit power (class 1) and -100 dBm receive sensitivity (125 kbps)
    • Zigbee: up to 8 dBm transmit power and -97 dBm receive sensitivity (250 kbps)
    • GNSS L1 (1575.42 MHz) receiver supporting GPS, Galileo, GLONASS, and BeiDou signal
      • Receive sensitivity: -163 dBm (tracking)
      • Integrated antenna with gain of ~2 dBi
    • Advanced IoT coexistence (AIC) allows concurrent operation of multiple radios in the 2.4 GHz band
    • Built-in trusted platform module (TPM) for enhanced security and anti-counterfeiting
    • Visual indicators for system and radio status (1x multi-color LED), auto-disable after 15min when up
    • Reset button: factory reset, LED mode control (normal/off)
    • Serial console interface (proprietary, USB-C physical jack)
    • Automatic thermal shutdown and recovery function
    Mounting
    • A mounting bracket holder has been pre-installed on the top of the AP. This bracket is used to secure the AP to any of the mount kits (sold separately); see the HPE Aruba Networking 670 Series Ordering Guide for details. The HPE Aruba Networking 670 Series Outdoor access points also share the same mounting hardware and accessories so upgrades from previous HPE Aruba Networking outdoor access points are quick and easy.
      • AP-OUT-MNT-V1A: Outdoor Pole/Wall Long Mount Kit
      • AP-270-MNT-V2: Outdoor Pole/Wall Short Mount Kit
      • AP-270-MNT-H1: Outdoor AP Hanging or Tilt Install Mount Kit
      • AP-270-MNT-H2: Outdoor Flush Wall or Ceiling Mount
      • AP-270-MNT-H3: Outdoor AP Hanging or Dual-Tilt Install Mount Kit
    Mechanical
    • AP-675
      • Dimensions/weight (unit only):
        • 290mm (W) x 288mm (D) x 312mm (H)
        • 11.4 in (W) x 11.3 in (D) x 12.3in (H)
        • 4kg / 8.8lbs
    • AP-677
      • Dimensions/weight (unit only):
        • 290 (W) x 288mm (D) x 171mm (H)
        • 11.4 in (W) x 11.3 in (D) x 6.7 in (H)
        • 3.6kg / 7.9lbs
    • AP-679
      • Dimensions/weight (unit only):
        • 290mm (W) x 288mm (D) x 171mm (H)
        • 11.4 in (W) x 11.3 in (D) x 6.7 in (H)
        • 3.8kg / 8.4lbs
    Environmental
    • Operating conditions
      • Temperature: -40 °C to +70 °C / -40 °F to 158 °F (no solar loading), -40 °C to +65 °C / -40 °F to 149 °F (with solar loading)
      • Humidity: 5% to 100% non-condensing internal
      • Rated for operation in all weather conditions
    • Storage and transportation conditions
      • Temperature: -40C to +70C / -40F to +158F
    • Operating Altitude: 3000m
    • Water and Dust
      • IP66/67
    • Salt Tolerance
      • Test to ASTM B117-07A Salt Spray 200hrs
    • Wind Survival: 150mph (GR-487)
    Reliability
    • Mean time between failure (MTBF): 500,562hrs (59.4 yrs.) at +25C ambient operating temperature.
    Regulatory compliance
    • FCC/ISED
    • CE marked
    • RED directive 2014/53/EU
    • IEC/EN 62368-1
    • EN 60601-1-1, EN60601-1-2
    • For more country-specific regulatory information and approvals, please see your HPE Aruba Networking representative.
    Regulatory model numbers
    • AP-675: APEX0675
    • AP-677: APEX0677
    • AP-679: APEX0679
    Certifications
    • Wi-Fi Alliance:
    • Bluetooth SIG
    • Ethernet Alliance (E0, PoE PD device, class 6)
    Minimum Operating System Software Versions
      • HPE Aruba Networking Wireless Operating System AOS-10.7.0.0 (AP-675, AP-677)
      • HPE Aruba Networking Wireless Operating System AOS-10.7.1.0 (AP-679)
      • HPE Aruba Networking Wireless Operating System AOS-8.12.0.0
      • HPE Aruba Networking Instant Operating System AOS-8.12.0.0 (no 6GHz support with Instant)
    • Learn more about our support services: https://www.arubanetworks.com/support-services/
Warranty

Related products

Learn about products that complement the 670 Series Outdoor APs to better suit your needs.

580 Series

  • Ultimate outdoor Wi-Fi 6 performance and speed
  • Bluetooth and 802.15.4/Zigbee radios with high power
  • Dual redundant power/port failover and support for AC
Aruba 570 シリーズ屋外用アクセス・ポイント

570 Series

  • High-performance Wi-Fi 6 outdoor access point
  • Built-in BLE and Zigbee support
  • Ideal for high-density outdoor environments
side by side image of 560 access point front and back

560 Series

  • Low-cost Wi-Fi 6 outdoor access point
  • Small form factor for maximum flexibility
  • Ideal for outdoor and warehouse environments

Ready to get started?