You are here: Home > CLI Commands > Just_CLI_Topics > ap regulatory reset

ap regulatory reset

ap regulatory-domain-profile <profile>

clone <profile>

country-code <code>

no ...

valid-11a-40mhz-channel-pair <valid-11a-40mhz-channel-pair>

valid-11a-80mhz-channel-group <valid-11a-80mhz-channel-group>

valid-11a-channel <num>

valid-11g-40mhz-channel-pair <valid-11g-40mhz-channel-pair>

valid-11g-channel <num>

Description

This command returns the Mobility Master to the factory default Regulatory-Cert.

Syntax

Parameter

Description

Default

<profile>

Name of this instance of the profile. The name must be 1-63 characters.

 

clone

Name of an existing regulatory domain profile from which parameter values are copied.

 

country-code

Code that represents the country in which the APs will operate. The country code determines the 802.11802.11 is an evolving family of specifications for wireless LANs developed by a working group of the Institute of Electrical and Electronics Engineers (IEEE). 802.11 standards use the Ethernet protocol and Carrier Sense Multiple Access with collision avoidance (CSMA/CA) for path sharing. wireless transmission spectrum.

Improper country code assignment can disrupt wireless transmissions. Most countries impose penalties and sanctions for operators of wireless networks with devices set to improper country codes.

 

Country code configured on the Mobility Master during initial setup.

no

Negates any configured parameter.

valid-11a-40mhz -channel-pair

Specify a channel pair valid for 40 MHzMegahertz operation in the 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. frequency bandBand refers to a specified range of frequencies of electromagnetic radiation. for the specified regulatory domain. The two channels must be separated by a dash.

Example:

36-40

44-48

52-56

Country code determines supported channel pairs

NOTE: Changing the country code causes the valid channel lists to be reset to the defaults for the country.

valid-11a-80mhz-channel-group

This parameter defines which 80 MHzMegahertz channels on the “a” bandBand refers to a specified range of frequencies of electromagnetic radiation. are available for assignment by ARMAdaptive Radio Management. ARM dynamically monitors and adjusts the network to ensure that all users are allowed ready access. It enables full utilization of the available spectrum to support maximum number of users by intelligently choosing the best RF channel and transmit power for APs in their current RF environment. and for Mobility Master to randomly assign if the user has not specified a channel. The channel numbers below correspond to channel center frequency.

valid-11a-
channel

Enter a single 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. channel number for 20 MHzMegahertz operation within the specified regulatory domain.

Country code determines supported channels

NOTE: Changing the country code causes the valid channel lists to be reset to the defaults for the country.

valid-11g-40mhz -channel-pair

Specify a channel pair valid for 40 MHzMegahertz operation in the 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. frequency bandBand refers to a specified range of frequencies of electromagnetic radiation. for the specified regulatory domain. The two channels must be separated by a dash.

Example:

1-5

2-6

7-11

Country code determines supported channel pairs

NOTE: Changing the country code causes the valid channel lists to be reset to the defaults for the country.

valid-11g-
channel

Enter a single 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. channel number for 20 MHzMegahertz operation within the specified regulatory domain.

 

Country code determines supported channels

NOTE: Changing the country code causes the valid channel lists to be reset to the defaults for the country.

Usage Guidelines

Use this command to return the Mobility Master to the factory default regulatory information.

Related Commands

Command

Description

show ap regulatory

This command displays information about the current regulatory certificate.

show ap allowed-channels

This command displays information about the supported channels.

Command History

Release

Modification

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms

Base operating system.

Enable mode on Mobility Master.

/*]]>*/