You are here: Home > CLI Commands > Just_CLI_Topics > ap system-profile

ap system-profile

ap system-profile <profile-name>

aeroscout-rtls-server ip-or-dns <ipaddr-or-dns> port <port> include-unassoc-sta {disable|enable}

airmatch-measure-duration <airmatch-measure-duration>

airmatch-report-enabled

airmatch-report-period <airmatch-report-period>

am-scan-rf-band {a | all | g}

ap-arp-attack-protection

ap-console-password <ap-console-password>

ap-console-protection

ap-deploy-hour

ap-poe-mode {failover | shared}

ap-usb-power-mode {auto | enable | disable}

bkup-band {a | all | g}

bkup-lms-ip <ipaddr>

bkup-lms-ipv6 <ipaddr>

bkup-mode {static | dynamic | off}

bkup-passwords <password>

ble-op-mode {Beaconing | Disabled | DynamicConsole | PersistentConsole}

bootstrap-threshold <number>

bridge-offload

clone {default | <source>}

console-enable

console-log-lvl

disable-tftp-image-upgrade

dns-domain <domain>

double-encrypt

driver-log-level <severity-level>

dscp-to-dot1p-priority-mapping <dscp-to-dot1p-priority-mapping>

dual-5ghz-mode {automatic | disabled | enabled}

dump-server <dump-server>

dump-collection-profile

flex-radio-mode {2.4GHz|2.4GHz-and-5GHz|5GHz}

gre-offload

health-check [burst size <burst-size> | frequency <frequency> | mode <mode> | packet-size <packet-size>| report <report>| retries <retries>}

health-check-option

heartbeat-dscp <heartbeat-dscp>

heartbeat-interval <heartbeat-interval>

image-url <image-url>

ipm-enable

ipm-power-reduction-step-prio {all | ipm-step {cpu_throttle_25 | cpu_throttle_50 | cpu_throttle_75 | disable_alt_eth | disable_pse | disable_usb | radio_2ghz_chain_1x1 | radio_2ghz_chain_2x2 | radio_2ghz_chain_3x3 | radio_2ghz_power_3dB | radio_2ghz_power_6dB | radio_5ghz_chain_1x1 | radio_5ghz_chain_2x2 | radio_5ghz_chain_3x3 | radio_5ghz_power_3dB | radio_5ghz_power_6dB} priority <priority>}

led-mode {normal | off}

led-override

lms-hold-down-period <lms-hold-down-period>

lms-ip <lms-ip>

lms-ipv6 <lms-ipv6>

lms-ping-interval <lms-ping-interval>

lms-preemption

maintenance-mode

max-request-retries <max-request-retries>

mcast-aggr

mcast-aggr-allowed-vlan <vlan-list>

mgmt-dscp <mgmt-dscp>

mtu <mtu>

native-vlan-id <native-vlan-id>

no

number_ipsec_retries <number_ipsec_retries>

rap-bw-resv-1 acl <aclname> <bw-value> [priority <priority>]

rap-bw-resv-2 acl <acl-name> <bw-value> [priority <priority>]

rap-bw-resv-3 acl <acl-name> <bw-value> [priority <priority>]

rap-bw-total <rap-bw-total>

rap-corp-dns-server <ipv4 address>

rap-corp-dns-server_ ipv6 <ipv6 address>

rap-dhcp-default-router <rap-dhcp-default-router>

rap-dhcp-dns-server <rap-dhcp-dns-server>

rap-dhcp-lease <rap-dhcp-lease>

rap-dhcp-pool-end <rap-dhcp-pool-end>

rap-dhcp-pool-netmask <rap-dhcp-pool-netmask>

rap-dhcp-pool-start <rap-dhcp-pool-start>

rap-dhcp-server-id <rap-dhcp-server-id>

rap-dhcp-server-vlan <rap-dhcp-server-vlan>

rap-gre-mtu <rap-gre-mtu>

rap-local-network-access

recovery-mode {auto | legacy}

request-retry-interval <request-retry-interval>

rf-band <a | g>

rtls-server ip-or-dns <ip-or-dns> port <port> key <key> station-message-frequency <seconds> [include-unassoc-sta {enable | disable}]

rtls-server-compat_mode

secondary-master <secondary-master>

sesImagotag-esl-channel

sesImagotag-esl-serverip

session-acl <session-acl>

slow_timer_recovery

spanning-tree

syscontact <syscontact>

telnet

wids-ampdu-optimization

Description

This command configures an AP system profile.

Syntax

Parameter

Description

Range

Default

ap system-profile <profile>

Configures AP system profile. Give a name for this instance of the profile. The name must be 1–63 characters long.

default

aeroscout-rtls-
server

Enables the AP to send RFIDRadio Frequency Identification. RFID uses radio waves to automatically identify and track the information stored on a tag attached to an object. tag information to an AeroScout RTLSReal-Time Location Systems. RTLS automatically identifies and tracks the location of objects or people in real time, usually within a building or other contained area. server.

RTLSReal-Time Location Systems. RTLS automatically identifies and tracks the location of objects or people in real time, usually within a building or other contained area. station reporting includes information for APs and the clients that the AP has detected.

ip-or-dns <ip-or-dns>

IPv4/IPv6 address or the DNSDomain Name System. A DNS server functions as a phone book for the intranet and Internet users. It converts human-readable computer host names into IP addresses and IP addresses into host names. It stores several records for a domain name such as an address 'A' record, name server (NS), and mail exchanger (MX) records. The Address 'A' record is the most important record that is stored in a DNS server, because it provides the required IP address for a network peripheral or element. of the AeroScout server to which location reports are sent.

port <port>

Port number on the AeroScout server to which location reports are sent.

include-unassoc-sta
enable|disable

If you select the include-unassoc-sta enable option, the station reports will also include information about clients not associated to any AP. By default, unassociated clients are not included in station reports.

disabled

airmatch-measure-duration <airmatch-measure-duration>

Change the AirMatch RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. measurement duration from the default value of 5 minutes to any value in the range 5–60 minutes. A value of 0 disables AirMatch RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. environment measurements.

5–60 minutes, or 0 minutes to disable measurements

5 minutes

airmatch-report-enabled

Each AP in a Mobility Master deployment measures its RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. environment for a duration specified by airmatch-measure-duration, every 30 minutes by default. Mobility Master uses this information to compute an optimal solution.

enabled

airmatch-report-period <airmatch-report-period>

Change the frequency period which AirMatch starts measuring the RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. environment. The default value is 30 minutes and the supported range of values is 5–180 minutes.

5–180 minutes

30 minutes

am-scan-rf-band

Scanning bandBand refers to a specified range of frequencies of electromagnetic radiation. for multiple RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. radios.

a, g, all

all

a

Sets the scanning bandBand refers to a specified range of frequencies of electromagnetic radiation. to 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. only.

g

Sets the scanning bandBand refers to a specified range of frequencies of electromagnetic radiation. to 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. only.

all

Sets the scanning bandBand refers to a specified range of frequencies of electromagnetic radiation. to apply to all bandsBand refers to a specified range of frequencies of electromagnetic radiation..

ap-arp-attack-protection

Drop ARPAddress Resolution Protocol. ARP is used for mapping IP network address to the hardware MAC address of a device. packets coming from wired or wireless clients with AP gatewayGateway is a network node that allows traffic to flow in and out of the network. IP address. In other words, disallow ARPAddress Resolution Protocol. ARP is used for mapping IP network address to the hardware MAC address of a device. attack from untrusted ports.

enabled

ap-console-password <ap-console-password>

Set the AP console password on the managed device. If the user does not set any password, the managed device generates a default random password which can be viewed by executing the encrypt disable command followed by the show ap system-profile <profile-name> command.

6–32 characters

default random password

ap-console-protection

Enable the AP console password.

enabled

ap-deploy-hour

Configure hour-of-day for solution deployment for all radios of an AP. Overrides Airmatch profile if a valid hour is specified.

0–23

ap-poe-mode

{failover | shared}

Configure the required PoEPower over Ethernet. PoE is a technology for wired Ethernet LANs to carry electric power required for the device in the data cables. The IEEE 802.3af PoE standard provides up to 15.4 W of power on each port. mode on the AP platforms hat support dual PoEPower over Ethernet. PoE is a technology for wired Ethernet LANs to carry electric power required for the device in the data cables. The IEEE 802.3af PoE standard provides up to 15.4 W of power on each port. mode.

Failover: Enables the source PoEPower over Ethernet. PoE is a technology for wired Ethernet LANs to carry electric power required for the device in the data cables. The IEEE 802.3af PoE standard provides up to 15.4 W of power on each port. power from either of the EthernetEthernet is a network protocol for data transmission over LAN. ports.

Shared: Enables the combined power from both the PoEPower over Ethernet. PoE is a technology for wired Ethernet LANs to carry electric power required for the device in the data cables. The IEEE 802.3af PoE standard provides up to 15.4 W of power on each port. sources.

ap-usb-power-mode {auto|enable|disable}

Set the USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices. power mode to control the power to the USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices. port. Listed below are the power modes:

auto- Detect USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices.  power mode automatically

disable- Disable USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices.  power

enable- Enable USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices.  power

NOTE: This parameter can be configured only on AP-214, AP-215, AP-224, AP-225, AP-205H, AP-303H, AP-304, AP-305, AP-314, AP-315, AP-324, AP-325, AP-334, AP-335, AP-344, AP-345, AP-203R, and AP-203RP access points only.

auto

bkup-band a | all | g

BandBand refers to a specified range of frequencies of electromagnetic radiation. on which the Mobility Master broadcasts the backup ESSIDExtended Service Set Identifier. ESSID refers to the ID used for identifying an extended service set..

802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps., all bandsBand refers to a specified range of frequencies of electromagnetic radiation., or 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network.

all

bkup-lms-ip <bkup-lms-ip>

In multi-controller) networks, specifies the IP address of a backup to the IP address specified with the lms-ip parameter.

bkup-lms-ipv6 <bkup-lms-ipv6>

In multi-controller IPv6 networks, specifies the IPv6 address of a backup to the IPv6 address specified with the lms-ipv6 parameter.

bkup-mode
dynamic|off|static

This parameter allows AP console access using a backup ESSIDExtended Service Set Identifier. ESSID refers to the ID used for identifying an extended service set., allowing users to access an AP console after the AP has disconnected from the Mobility Master. When the AP advertises a backup ESSIDExtended Service Set Identifier. ESSID refers to the ID used for identifying an extended service set. in either static or dynamic mode, a user is able to access and debug the AP remotely through a virtual AP.

Select dynamic or static to enable this feature and select the mode by which the Mobility Master broadcasts the backup ESSIDExtended Service Set Identifier. ESSID refers to the ID used for identifying an extended service set.. This feature is disabled by default.

dynamic, off, or static

off

bkup-passwords <bkup-passwords>

Allows client access to adjust the bandBand refers to a specified range of frequencies of electromagnetic radiation. and mode settings for the backup ESSIDExtended Service Set Identifier. ESSID refers to the ID used for identifying an extended service set..

ble-op-mode

{Beaconing |

Disabled |

DynamicConsole |

PersistentConsole}

Determines how the built-in BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. chip in the AP functions. BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. chip can be in one of the following four modes:

Beaconing: The built-in BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. chip of the AP functions as an iBeacon combined with beacon management functionality.

Disabled: The built-in BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. chip of the AP is turned off. This is the default setting.

DynamicConsole: The built-in chip of the AP functions as a regular iBeacon combined with beacon management functionality. However, when the link to the Mobility Master is lost, the built-in chip temporarily enables access to the AP console over BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption.. This state of the BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. device may be rolled back to any of the other modes if the AP receives a different configuration setting for the ble-op-mode parameter from the new LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. .

PersistentConsole: The built-in chip of the AP provides access to the AP console over BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. using a mobile application. This functionality is the superset of the Beaconing mode.

NOTE: BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. is disabled on ArubaOS FIPSFederal Information Processing Standards. FIPS refers to a set of standards that describe document processing, encryption algorithms, and other information technology standards for use within non-military government agencies, and by government contractors and vendors who work with these agencies. build.

Disabled

ble-token <ble-token>

The BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. endpoint authorization token is a text string of 1–255 characters used by the BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. to authorize to and securely communicate with the BMCBeacon Management Console. BMC manages and monitors beacons from the BLE devices. The BLE devices are used for location tracking and proximity detection.. This token is unique for each deployment.

1–255 characters

ble-url <ble-url>

URLUniform Resource Locator. URL is a global address used for locating web resources on the Internet. of the Meridian server to which the BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. sends monitoring data.

bootstrap-threshold <bootstrap-threshold>

Configures number of consecutive missed heartbeats on a GREGeneric Routing Encapsulation. GRE is an IP encapsulation protocol that is used to transport packets over a network. tunnel (heartbeats are sent once per second on each tunnel) before an AP rebootstraps. On the Mobility Master, the GREGeneric Routing Encapsulation. GRE is an IP encapsulation protocol that is used to transport packets over a network. tunnel timeout is 1.5 x bootstrap-threshold; the tunnel is torn down after this number of seconds of inactivity on the tunnel.

1–65535

8

bridge-offload

Enables the hardware acceleration of bridge traffic.

clone <source>

Name of an existing AP system profile from which parameter values are copied.

console-enable

Enables console port on the AP.

enabled

console-log-lvl

{alerts | critical |
debugging |
emergencies |
errors |
informational |
notifications |
warnings}

Specifies the level of driver log prints sent to AP console. The description of different log levels are as follows:

emergencies: To send driver log prints when system is unusable

alerts: To send driver log prints when Immediate action is needed

critical: To send driver log prints when critical conditions exist

errors: To send driver log prints when there are error conditions

warnings: To send driver log prints for warning conditions

notifications: To send driver log prints when a normal, but significant condition occurs

informational: To send driver log prints for informational messages

debugging: To send driver log prints for debugging messages

NOTE: Do not change the console log level without prior supervision from the Aruba Technical Support team.

emergencies

dscp-to-dot1p-priority-mapping

Configures semicolon- separated mapping between IP DSCPDifferentiated Services Code Point. DSCP is a 6-bit packet header value used for traffic classification and priority assignment. value and VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. 802.1p priority.

Format: <DSCPDifferentiated Services Code Point. DSCP is a 6-bit packet header value used for traffic classification and priority assignment. range/list (0-63)>:<802.1p value (0-7)>

Format Example:

24:4;32,34:3;45-56:1;57-60,62:7

dns-domain <dns-domain>

Name of domain that is resolved by corporate DNSDomain Name System. A DNS server functions as a phone book for the intranet and Internet users. It converts human-readable computer host names into IP addresses and IP addresses into host names. It stores several records for a domain name such as an address 'A' record, name server (NS), and mail exchanger (MX) records. The Address 'A' record is the most important record that is stored in a DNS server, because it provides the required IP address for a network peripheral or element. servers. Use this parameter when configuring split tunnel.

double-encrypt

This parameter applies only to remote APsRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link.. Use double encryption for traffic to and from a wireless client that is connected to a tunneled SSIDService Set Identifier. SSID is a name given to a WLAN and is used by the client to access a WLAN network..

When enabled, all traffic is re-encrypted in the IPsecInternet Protocol security. IPsec is a protocol suite for secure IP communications that authenticates and encrypts each IP packet in a communication session. tunnel. When disabled, the wireless frame is only encapsulated inside the IPsecInternet Protocol security. IPsec is a protocol suite for secure IP communications that authenticates and encrypts each IP packet in a communication session. tunnel.

All other types of data traffic between the Mobility Master and the AP (wired traffic and traffic from a split-tunneled SSIDService Set Identifier. SSID is a name given to a WLAN and is used by the client to access a WLAN network.) are always encrypted in the IPsecInternet Protocol security. IPsec is a protocol suite for secure IP communications that authenticates and encrypts each IP packet in a communication session. tunnel.

disabled

driver-log-level

{alerts | critical |
debugging | emergencies |
errors | informational |
notifications | warnings}

Configures the level of driver log prints sent to syslog server. The description of different log levels are as follows:

emergencies: To send driver log prints when system is unusable

alerts: To send driver log prints when Immediate action is needed

critical: To send driver log prints when critical conditions exist

errors: To send driver log prints when ther are error conditions

warnings: To send driver log prints for warning conditions

notifications: To send driver log prints when a normal, but significant condition occurs

informational: To send driver log prints for informational messages

debugging: To send driver log prints for debugging messages

warnings

dual-5ghz-mode

{automatic|disabled|enabled}

Mode for Dual 5GHz APs:

automatic: Dual 5GHz Mode is enabled or disabled automatically.

disabled: Dual 5GHz mode is disabled.

enabled: both radios operate on 5GHz bandBand refers to a specified range of frequencies of electromagnetic radiation..

 

NOTE: The dual-5ghz-mode parameter is supported only on 340 Series (AP-344 and AP-345) access points. However, the automatic mode is not supported on AP-344 access points.

For example, if the configuration for dual-5ghz-mode is set to automatic, AP-344 access points do not support a dynamic mode change. Users must manually set dual-5ghz-mode to Enabled if they require AP-344 access points to operate in the dual 5GHz mode. Additionally, users must purchase the required dual 5GHz external antenna.

automatic

NOTE:  

In a master-local or a stand-alone controller mode, automatic is treated as disabled.

In a Mobility Master- Managed Device mode, automatic indicates that AirMatch determines when to modify the operating mode from dual bandBand refers to a specified range of frequencies of electromagnetic radiation. to the dual 5GHz mode.

dump-collection-profile

{default | profile-name}

Specifies the profile for collecting core dump when an AP process crashes.

flex-radio-mode {2.4GHz|2.4GHz-and-5GHz|5GHz}

The mode for flexible Radios. Use the following parameters:

2.4GHz: The radio operates on 2.4GHz.

2.4GHz-and-5GHz: The radio operates on both 2.4GHz and 5GHz.

5GHz: The radio operates on 5GHz.

gre-offload

HW acceleration of GREGeneric Routing Encapsulation. GRE is an IP encapsulation protocol that is used to transport packets over a network. traffic (for test purpose only)

Disabled

health-check

The AP Health check feature configured via the health-check parameters uses ping probes to check reachablility and latency levels for the connection between the AP and the managed device. Recorded latency information appears in the output of the show ap ip health-check command. If the managed device IP address becomes unreachable from the AP uplink, this feature records the time that the connection failed, and saves that information in a log file (tmp or ap_hcm_log) on the AP.

burst-size <size>

Number of probes to be sent during the probe frequency interval defined by the frequency health-check parameter.

1–16 probes

5 probes

frequency <frequency>

Probe interval, in seconds. The WANWide Area Network. WAN is a telecommunications network or computer network that extends over a large geographical distance. health-check feature sends the number of probes defined by the burst-size parameter during each frequency interval defined by this frequency parameter.

10–300 seconds

10 seconds

mode <mode>

Ping probe mode is the only mode currently supported by this feature.

ping

packet-size <packet-size>

The size, in bytes, of a ping datagram.

10–2000 bytes

32 bytes

report <report>

Number of seconds between health check reports sent from the AP to the controller. usage reports.

60–3600 seconds

60 seconds

retries <retries>

Number of times the attempts to resend a probe.

1–10 retries

3 retries

health-check-option

Issue the ap system-profile <profile> health-check-option command to enable the AP Health check feature.

disabled

heartbeat-dscp <heartbeat-dscp>

Define the DSCPDifferentiated Services Code Point. DSCP is a 6-bit packet header value used for traffic classification and priority assignment. value of AP heartbeats. Use this feature to prioritize AP heartbeats and prevent the AP from losing connectivity with the Mobility Master over high-latency or low-bandwidth WANWide Area Network. WAN is a telecommunications network or computer network that extends over a large geographical distance. connections.

0–63

0

heartbeat-in <heartbeat-interval>

Set the interval between heartbeat messages between a remote or campus APCampus APs are used in private networks where APs connect over private links (LAN, WLAN, WAN or MPLS) and terminate directly on controllers. Campus APs are deployed as part of the indoor campus solution in enterprise office buildings, warehouses, hospitals, universities, and so on. and its associated Mobility Master. An increase in the heartbeat interval increases the time it will take for an AP to detect the loss in connectivity to the Mobility Master, but can reduce internet bandwidth consumed by a remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link..

1–60 seconds

1 second

image-url <image-url>

Provide the image URLUniform Resource Locator. URL is a global address used for locating web resources on the Internet. for an alternate AP image.

ipm-enable

Enables the IPMIntelligent Power Monitoring. IPM is a feature supported on certain APs that actively measures the power utilization of an AP and dynamically adapts to the power resources. system.

disabled

ipm-power-reduction-step-prio all

Sets up all the IPMIntelligent Power Monitoring. IPM is a feature supported on certain APs that actively measures the power utilization of an AP and dynamically adapts to the power resources. power reduction steps.

ipm-power-reduction-step-prio ipm-step

Sets IPMIntelligent Power Monitoring. IPM is a feature supported on certain APs that actively measures the power utilization of an AP and dynamically adapts to the power resources. power reduction steps.

cpu_throttle_25

Configure this option to reduce the CPUCentral Processing Unit. A CPU is an electronic circuitry in a computer for processing instructions. frequency to 25%.

 

 

cpu_throttle_50

Configure this option to reduce the CPUCentral Processing Unit. A CPU is an electronic circuitry in a computer for processing instructions. frequency to 50%.

 

 

cpu_throttle_75

Configure this option to reduce the CPUCentral Processing Unit. A CPU is an electronic circuitry in a computer for processing instructions. frequency to 75%.

 

 

disable_alt_eth

Disables the 2nd EthernetEthernet is a network protocol for data transmission over LAN. port.

 

 

disable_pse

Disables PSE.

 

 

disable_usb

Disables the USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices. .

 

 

radio_2ghz_chain_1x1

Configure this option to reduce 2 GHzGigahertz. chains to 1x1.

 

 

radio_2ghz_chain_2x2

Configure this option to reduce 2 GHzGigahertz. chains to 2x2.

 

 

radio_2ghz_chain_3x3

Configure this option to reduce 2 GHzGigahertz. chains to 3x3.

 

 

radio_2ghz_power_3dB

Configure this option to reduce the 2 GHzGigahertz. radio power by 3 dBDecibel. Unit of measure for sound or noise and is the difference or ratio between two signal levels. from maximum.

 

 

radio_2ghz_power_6dB

Configure this option to reduce the 2 GHzGigahertz. radio power by 6 dBDecibel. Unit of measure for sound or noise and is the difference or ratio between two signal levels. from maximum.

 

 

radio_5ghz_chain_1x1

Configure this option to reduce 5 GHzGigahertz. chains to 1x1.

 

 

radio_5ghz_chain_2x2

Configure this option to reduce 5 GHzGigahertz. chains to 2x2.

 

 

radio_5ghz_chain_3x3

Configure this option to reduce 5 GHzGigahertz. chains to 3x3.

 

 

radio_5ghz_chain_4x4

Configure this option to reduce 5 GHzGigahertz. chains to 4x4.

   

radio_5ghz_chain_5x5

Configure this option to reduce 5 GHzGigahertz. chains to 5x5.

   

radio_5ghz_chain_6x6

Configure this option to reduce 5 GHzGigahertz. chains to 6x6.

   

radio_5ghz_chain_7x7

Configure this option to reduce 5 GHzGigahertz. chains to 7x7.

   

radio_5ghz_power_3dB

Configure this option to reduce the 5 GHzGigahertz. radio power by 3 dBDecibel. Unit of measure for sound or noise and is the difference or ratio between two signal levels. from maximum.

 

 

radio_5ghz_power_6dB

Configure this option to reduce the 5 GHzGigahertz. radio power by 6 dBDecibel. Unit of measure for sound or noise and is the difference or ratio between two signal levels. from maximum.

 

 

priority <priority>

Sets the priorities for IPMIntelligent Power Monitoring. IPM is a feature supported on certain APs that actively measures the power utilization of an AP and dynamically adapts to the power resources. power reduction steps.

 

 

led-mode

The operating mode for the AP LEDs. This option is available on all 802.11n802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz. indoor AP platforms.

normal

normal

Display LEDs in normal mode.

off

Turn off all LEDs.

led-override

Override the LEDLight Emitting Diode. LED is a semiconductor light source that emits light when an electric current passes through it. action for single-LEDLight Emitting Diode. LED is a semiconductor light source that emits light when an electric current passes through it. APs in normal LEDLight Emitting Diode. LED is a semiconductor light source that emits light when an electric current passes through it. operating mode. If enabled, this feature disables the LEDLight Emitting Diode. LED is a semiconductor light source that emits light when an electric current passes through it. auto-turn-off function.

disabled

lms-hold-down-
period

Time, in seconds, that the primary LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. must be available before an AP returns to that LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. after failover.

1–3600 seconds

600
seconds

lms-ip <lms-ip>

In multi-controller networks, this parameter specifies the IP address of the LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. —the Mobility Master—which is responsible for terminating user traffic from the APs, and processing and forwarding the traffic to the wired network. This can be the IP address of the managed device or Mobility Master.

When using redundant managed device as the LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. , set this parameter to be the VRRPVirtual Router Redundancy Protocol. VRRP is an election protocol that dynamically assigns responsibility for a virtual router to one of the VRRP routers on a LAN. IP address to ensure that APs always have an active IP address with which to terminate sessions.

NOTE: If the LMS-IP is blank, the access point will remain on the managed device that it finds using methods like DNS or DHCP. If an IP address is configured for the LMS IP parameter, the AP will be immediately redirected to the managed device at that address.

lms-ipv6 <lms-ipv6>

In multi-controller IPv6 networks, specify the IPv6 address of the LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. —the Mobility Master—which is responsible for terminating user traffic from the APs, and processing and forwarding the traffic to the wired network. This can be the IP address of the managed device or Mobility Master.

When using redundant managed device as the LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. , set this parameter to be the VRRPVirtual Router Redundancy Protocol. VRRP is an election protocol that dynamically assigns responsibility for a virtual router to one of the VRRP routers on a LAN. IP address to ensure that APs always have an active IP address with which to terminate sessions.

lms-ping-interval <lms-ping-interval>

Specifies the interval at which application level ping needs to be sent to Mobility Master to check the reachability. Applicable only for Remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link..

NOTE: If this parameter is changed, UDPUser Datagram Protocol. UDP is a part of the TCP/IP family of protocols used for data transfer. UDP is typically used for streaming media. UDP is a stateless protocol, which means it does not acknowledge that the packets being sent have been received. session timeout on an intermediate router which performs the NATNetwork Address Translation. NAT is a method of remapping one IP address space into another by modifying network address information in Internet Protocol (IP) datagram packet headers while they are in transit across a traffic routing device. function should be set accordingly. The preferred timeout value is (lms-ping-interval + 30 seconds).

10–60 seconds

20
seconds

lms-preemption

Automatically reverts to the primary LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. IP address when it becomes available.

disabled

maintenance-
mode

Enable or disable AP maintenance mode.

This setting is useful when deploying, maintaining, or upgrading the network.

If enabled, APs stop flooding unnecessary traps and syslog messages to NMSNetwork Management System. NMS is a set of hardware and/or software tools that allow an IT professional to supervise the individual components of a network within a larger network management framework. systems or network operations centers when deploying, maintaining, or upgrading the network. The Mobility Master still generates debug syslog messages if debug logging is enabled.

disabled

max-request-retries <max-request-retries>

Maximum number of times to retry AP-generated requests, including keepaliveSignal sent at periodic intervals from one device to another to verify that the link between the two devices is working. If no reply is received, data will be sent by a different path until the link is restored. A keepalive can also be used to indicate that the connection should be preserved so that the receiving device does not consider it timed out and drop it. messages. After the maximum number of retries, the AP either tries the IP address specified by the bkup-lms-ip (if configured) or reboots.

1–65535

10

mcast-aggr

Enable multicast aggregation at AP.

disabled

mcast-aggr-allowed-vlan <vlan-list>

Enable list of VLANsVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. where AP multicast aggregation is allowed.

disabled

mgmt-dscp <mgmt-dscp>

Sets the DSCPDifferentiated Services Code Point. DSCP is a 6-bit packet header value used for traffic classification and priority assignment. value of AP management packets.

0–63

mtu

MTUMaximum Transmission Unit. MTU is the largest size packet or frame specified in octets (eight-bit bytes) that can be sent in networks such as the Internet., in bytes, on the wired link for the AP.

1024–1578

native-vlan-id <native-vlan-id>

Native VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. for bridge mode virtual APs (frames on the native VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. are not tagged with 802.1q tags).

1

no

Negates any configured parameter.

number-ipsec-retries <number_ipsec_retries>

The number of times the AP will attempt to recreate an IPsecInternet Protocol security. IPsec is a protocol suite for secure IP communications that authenticates and encrypts each IP packet in a communication session. tunnel with the Mobility Master before the AP will reboot. A value of 0 disables the reboot.

1–1000

85

rap-bw-resv-1 acl <aclname>

[priority <priority>]

Session ACLsAccess Control List. ACL is a common way of restricting certain types of traffic on a physical port. with uplink bandwidth reservation in KbpsKilobits per second.. You can specify up to three session ACLsAccess Control List. ACL is a common way of restricting certain types of traffic on a physical port. to reserve uplink bandwidth. The sum of the three uplink bandwidths should not exceed the rap-bw-total value. BW value is in KbpsKilobits per second..

Optionally, you can specify the priority for class 1, class 2, and class 3 traffic.

rap-bw-resv-2 acl <aclname> <bwvalue> [priority <priority>]

rap-bw-resv-3 acl <aclname> [priority <priority>]

rap-bw-total <rap-bw-total>

This is the total reserved uplink bandwidth (in KbpsKilobits per second.).

rap-corp-dns-server <ipv4 address>

IPv4 address of the Corporate DNSDomain Name System. A DNS server functions as a phone book for the intranet and Internet users. It converts human-readable computer host names into IP addresses and IP addresses into host names. It stores several records for a domain name such as an address 'A' record, name server (NS), and mail exchanger (MX) records. The Address 'A' record is the most important record that is stored in a DNS server, because it provides the required IP address for a network peripheral or element. server

__

__

rap-corp-dns-server_ ipv6 <ipv6 address>

IPv6 address of the Corporate DNSDomain Name System. A DNS server functions as a phone book for the intranet and Internet users. It converts human-readable computer host names into IP addresses and IP addresses into host names. It stores several records for a domain name such as an address 'A' record, name server (NS), and mail exchanger (MX) records. The Address 'A' record is the most important record that is stored in a DNS server, because it provides the required IP address for a network peripheral or element. server

__

__

rap-dhcp-default-router <rap-dhcp-default-router>

IP address for the default DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  router.

192.168.11.1

rap-dhcp-dns-server <rap-dhcp-dns-server>

IP address of the DNSDomain Name System. A DNS server functions as a phone book for the intranet and Internet users. It converts human-readable computer host names into IP addresses and IP addresses into host names. It stores several records for a domain name such as an address 'A' record, name server (NS), and mail exchanger (MX) records. The Address 'A' record is the most important record that is stored in a DNS server, because it provides the required IP address for a network peripheral or element. server.

192.168.11.1

rap-dhcp-lease <rap-dhcp-lease>

The amount of days that the assigned IP address is valid for the client. Specify the lease in <days>.

0 indicates the IP address is always valid; the lease does not expire.

0–30

0

rap-dhcp-pool-end <rap-dhcp-pool-end>

Configures a DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  pool for remote APsRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link.. This is the last IP address of the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  pool.

192.168.11.254

rap-dhcp-pool-netmask <rap-dhcp-pool-netmask>

Configures a DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  pool for remote APsRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link.. This is the netmaskNetmask is a 32-bit mask used for segregating IP address into subnets. Netmask defines the class and range of IP addresses. used for the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  pool.

255.255.255.0

rap-dhcp-pool-start <rap-dhcp-pool-start>

Configures a DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  pool for remote APsRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link.. This is the first IP address of the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  pool.

192.168.11.2

rap-dhcp-server-id <rap-dhcp-server-id>

IP address used as the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server identifier.

 

192.168.11.1

rap-dhcp-server-vlan <rap-dhcp-server-vlan>

VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. ID of the remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link. DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server used if the Mobility Master is unavailable. This VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. enables the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server on the AP (also known as the remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link. DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN.). If you enter the native VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. ID, the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server is unavailable.

rap-gre-mtu <rap-gre-mtu>

Configures the maximum size of the GREGeneric Routing Encapsulation. GRE is an IP encapsulation protocol that is used to transport packets over a network. packets exchanged between a Remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link. and the Mobility Master.

1024–1578 bytes

1200 bytes

rap-local-network -access

Enable or disable local network access across VLANsVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. in a Remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link..

disabled

recovery-mode {legacy | auto}

Select either the legacy recovery mode or the auto mode (fast recovery).

legacy— On detecting a firmware assert, the AP transfers the core-dump to the managed device and executes an AP reboot.

auto—On detecting a firmware assert, the AP executes the fast recovery process in the radio affected instead of rebooting the AP. This reduces the downtime of the AP in the network. If the AP detects a coredump with a valuable information during a firmware assert, then it transfers the core dump to the managed device and the AP reboots.

legacy

request-retry-interval <request-retry-interval>

Interval, in seconds, between the first and second retries of AP-generated requests. If the configured interval is less than 30 seconds, the interval for subsequent retries is increased up to 30 seconds.

1–65535 seconds

10 seconds

rf-band {a | g}

For APs that support both a and b/g RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. bandsBand refers to a specified range of frequencies of electromagnetic radiation., RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. bandBand refers to a specified range of frequencies of electromagnetic radiation. in which the AP should operate:

g = 2.4 GHzGigahertz.

a = 5 GHzGigahertz.

g

rtls-server

Enables the AP to send RFIDRadio Frequency Identification. RFID uses radio waves to automatically identify and track the information stored on a tag attached to an object. tag information to an RTLSReal-Time Location Systems. RTLS automatically identifies and tracks the location of objects or people in real time, usually within a building or other contained area. server.

ip-or-dns

IPv4/IPv6 address or the DNSDomain Name System. A DNS server functions as a phone book for the intranet and Internet users. It converts human-readable computer host names into IP addresses and IP addresses into host names. It stores several records for a domain name such as an address 'A' record, name server (NS), and mail exchanger (MX) records. The Address 'A' record is the most important record that is stored in a DNS server, because it provides the required IP address for a network peripheral or element. of the RTLSReal-Time Location Systems. RTLS automatically identifies and tracks the location of objects or people in real time, usually within a building or other contained area. server to which location reports are sent.

port

Port number on the server to which location reports are sent.

key

Shared secret key.

station-message-frequency

Indicates how often packets are sent to the server.

1–3600 seconds

30 seconds

[include-unassoc-sta
{enable | disable}]

RTLSReal-Time Location Systems. RTLS automatically identifies and tracks the location of objects or people in real time, usually within a building or other contained area. station reporting includes information for APs and the clients that the AP has detected. If you include the include-unassoc-sta parameter, the station reports will also include information about clients not associated to any AP. By default, unassociated clients are not included in station reports.

disabled

rtls-server-compat_mode

The compatibility mode controls the format of tag frames forwarded to the RTLSReal-Time Location Systems. RTLS automatically identifies and tracks the location of objects or people in real time, usually within a building or other contained area. server. Enabling this mode will enable legacy format (includes a 2 byte padding), and disabling this mode will remove the padding. The tag frame format will be the same across all AP models.

secondary-master
<secondary-master>

Assigns a remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link. as a secondary Mobility Master in the event the primary Mobility Master can not be reached.

sesImagotag-esl-channel

Sets the channel of SES-imagotag ESL Radio.

NOTE: There are 11 pre-defined, independent radio channels that you can configure. The recommended channels are 3, 5, 8, 9, and 10 as they connect faster. These channels do not correspond to standard 802.11802.11 is an evolving family of specifications for wireless LANs developed by a working group of the Institute of Electrical and Electronics Engineers (IEEE). 802.11 standards use the Ethernet protocol and Carrier Sense Multiple Access with collision avoidance (CSMA/CA) for path sharing. channels.

0–10

sesimagotag-esl-serverip

Sets the IP Address of SES-imagotag ESL Server. Adding server IP addresses allows bulk management and control of multiple servers at the same time.

session-acl <session-acl>

Session ACLAccess Control List. ACL is a common way of restricting certain types of traffic on a physical port. configured with the ip access-list session command.

NOTE: This parameter requires the PEFNGPolicy Enforcement Firewall. PEF also known as PEFNG provides context-based controls to enforce application-layer security and prioritization. The customers using Aruba mobility controllers can avail PEF features and services by obtaining a PEF license. PEF for VPN users—Customers with PEF for VPN license can apply firewall policies to the user traffic routed to a controller through a VPN tunnel. license.

slow_timer_recovery

If you enable this option, ArubaOS checks for a slow CPUCentral Processing Unit. A CPU is an electronic circuitry in a computer for processing instructions. timer, and if it detects an issue, it restarts the AP without logging a reason for the reboot. This feature is supported on RAP-108 or RAP-109 access points.

disabled

spanning-tree

Enables the spanning-tree protocol.

disabled

syscontact

SNMPSimple Network Management Protocol. SNMP is a TCP/IP standard protocol for managing devices on IP networks. Devices that typically support SNMP include routers, switches, servers, workstations, printers, modem racks, and more. It is used mostly in network management systems to monitor network-attached devices for conditions that warrant administrative attention.  system contact information.

telnet

Enables or disables telnet to the AP.

disabled

wids-ampdu-optimization

Enables or disables WIDSWireless Intrusion Detection System. WIDS is an application that detects the attacks on a wireless network or wireless system. aggregate MPDUMAC Protocol Data Unit. MPDU is a message exchanged between MAC entities in a communication system based on the layered OSI model. optimization.

disabled

Usage Guidelines

The AP system profile configures AP administrative operations, such as AirMatch and AP health check options and logging levels.

By default, each AP in a Mobility Master deployment measures its RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. environment for a 5-minute duration, every 30 minutes.  Mobility Master uses this information to compute an optimal solution, then deploys the latest RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. plan by sending updated settings to the APs. Use the airmatch settings in the ap system profile to modify these default report intervals, or to disable or reenable AirMatch reports to the APs.

The AP Health check feature configured via the health-check parameters uses ping probes to check reachablility and latency levels for the connection between the AP and the managed devices. Recorded latency information appears in the output of the show ap ip health-check command. If the managed device IP address becomes unreachable from the AP uplink, this feature records the time that the connection failed, and saves that information in a log file (tmp or ap_hcm_log) on the AP.

Starting from ArubaOS 8.2.0.0, the no ipm-power-reduction-step-prio ipm-step <ipm-step> priority <priority number> subcommand for the ap system-profile <profile> command set is simplified. If you want to remove one step or priority, you only need to specify the step and not the priority. For example: no ipm-power-reduction-step-prio ipm-step <ipm-step>.

Example

To set the Dual 5GHz mode option for 340 Series access points through the CLICommand-Line Interface. A console interface with a command line shell that allows users to execute text input as commands and convert these commands to appropriate functions., use the following commands:

(host) [mynode] (config) #ap system profile <profile-name>

(host) [mynode] (AP system profile "<profile-name>") #dual-5ghz-mode enabled

Execute the following commands to configure LACPLink Aggregation Control Protocol. LACP is used for the collective handling of multiple physical ports that can be seen as a single channel for network traffic purposes. and AP LACPLink Aggregation Control Protocol. LACP is used for the collective handling of multiple physical ports that can be seen as a single channel for network traffic purposes. LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. map information settings.

(host) [mynode] (config) #ap system-profile LACP

(host) [mynode] (AP system profile "LACP") #lms-ip 192.0.2.1

(host) [mynode] (AP system profile "LACP") #exit

(host) [mynode] (config) #ap-lacp-striping-ip

(host) [mynode] (AP LACP LMS map information) #striping-ip 192.0.2.2 lms 192.0.2.1

(host) [mynode] (AP LACP LMS map information) #aplacp-enable

For more information on configuring LACPLink Aggregation Control Protocol. LACP is used for the collective handling of multiple physical ports that can be seen as a single channel for network traffic purposes. support, including important pre-deployment considerations and troubleshooting information, refer to the Link Aggregation Support .

Execute the following command to remove one IPMIntelligent Power Monitoring. IPM is a feature supported on certain APs that actively measures the power utilization of an AP and dynamically adapts to the power resources. step or priotity from the AP system profile, "default":

(host) [mynode] (config) #ap system-profile default

(host) [mynode] (AP system profile "default") #no ipm-power-reduction-step-prio ipm-step cpu_throttle_50

Execute the following command to remove all IPMIntelligent Power Monitoring. IPM is a feature supported on certain APs that actively measures the power utilization of an AP and dynamically adapts to the power resources. priorities set for an AP system profile:

(host) [mynode] (AP system profile "default") #no ipm-power-reduction-step-prio all

Use the following commands to configure the recovery mode parameter for 300 Series access points:

(host) [mynode] (config) #ap system-profile <profile-name>

(host) [mynode] (AP system profile "<profile-name>") #recovery-mode auto

Command History

Release

Modification

ArubaOS 8.5.0.0

The following parameters were added:

rap-corp-dns-server <ipv4 address>

rap-corp-dns-server_ ipv6 <ipv6 address>

ArubaOS 8.4.0.0

The following changes were introduced:

The IPv6 address support was added to the ip-or-dns parameter.

The ap-usb-power-mode and wids-ampdu-optimization parameters were added.

The sesImagotag-esl-channel and sesImagotag-esl-serverip parameters were added.

The ap-usb-power-override parameter was deprecated.

The following parameters are added:

radio_5ghz_chain_4x4

radio_5ghz_chain_5x5

radio_5ghz_chain_6x6

radio_5ghz_chain_7x7

ArubaOS 8.3.0.0

The following new parameters were added:

dual-5ghz-mode

recovery-mode

ap-deploy-hour

ArubaOS 8.2.0.0

The all sub-parameter was added to the ipm-power-reduction-step-prio parameter.

The no ipm-power-reduction-step-prio ipm-step <ipm-step> priority <priority number> parameter was changed to no ipm-power-reduction-step-prio ipm-step <ipm-step>.

The flex-radio-mode parameter was added.

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms

Base operating system, except for noted parameters.

Config mode on Mobility Master.

/*]]>*/