You are here: Home > CLI Commands > Just_CLI_Topics > rf ht-radio-profile

rf ht-radio-profile

rf ht-radio-profile <profile>

40MHz-intolerance

bss-color <bss-color>

clone <profile>

diversity-spreading-workaround

honor-40MHz-intolerance

no

Description

This command configures high-throughput AP radio settings. High-throughput features use the IEEEInstitute of Electrical and Electronics Engineers. 802.11n802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz. standard.

Syntax

Parameter

Description

Range

Default

<profile>

Name of this instance of the profile. The name must be 1-63 characters.

Default Options:

“Default-a” is generally used in association with high-throughput devices running on the 5 GHzGigahertz. frequency bandBand refers to a specified range of frequencies of electromagnetic radiation., see rf dot11a-radio-profile.

“Default-g” is generally used in association with high-throughput devices running on the 2.4 GHzGigahertz. frequency bandBand refers to a specified range of frequencies of electromagnetic radiation., see rf dot11g-radio-profile.

“Default” is generally used when the same ht-radio-profile is desired for use with both frequency bandsBand refers to a specified range of frequencies of electromagnetic radiation..

default-a
default-g
default

40MHz-
intolerance

Controls whether or not APs using this radio profile will advertise intolerance of 40 MHzMegahertz operation. By default, 40 MHzMegahertz operation is allowed.

disabled

bss-color

Enables different colors for each category of BSSIDsBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly..

NOTE: The default value of 0 indicates that the BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly. color is assigned automatically.

0—63

0

clone

Name of an existing high-throughput radio profile from which parameter values are copied.

honor-40MHz-
intolerance

When enabled, the radio will stop using the 40 MHzMegahertz channels if the 40 MHzMegahertz intolerance indication is received from another AP or station.

enabled

no

Negates any configured parameter.

diversity-spreading -workaround

When this feature is enabled, all legacy transmissions will be sent using a single antenna. This enables interoperability for legacy or high-throughput stations that cannot decode 802.11n802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz. cyclic shift diversity (CSD) data.

This feature is disabled by default and should be kept disabled unless necessary.

 

disabled

Usage Guidelines

The ht-radio-profile configures high-throughput settings for networks utilizing the IEEEInstitute of Electrical and Electronics Engineers. 802.11n802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz. standard, which supports 40 MHZ channels and operates in both the 2.4 GHZ and 5 GHZ frequency bandsBand refers to a specified range of frequencies of electromagnetic radiation..  

Most transmissions to high throughput (HT) stations are sent through multiple antennas using cyclic shift diversity (CSD). When you enable the disable-diversity-spreading parameter, CSD is disabled and only one antenna transmits data, even if they are being sent to high-throughput stations. Use this feature to turn off antenna diversity when the AP must support legacy clients such as Cisco 7921g VoIPVoice over IP. VoIP allows transmission of voice and multimedia content over an IP network. phones, or older 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. clients (e.g. Intel Centrino clients). Note, however, that enabling this feature can reduce overall throughput rates.

The ht-radio-profile you wish to use must be assigned to a dot11a and/or dot11g-radio-profile. You can assign the same profile or different profiles to the 2.4 GHZ and 5 GHZ frequency bandsBand refers to a specified range of frequencies of electromagnetic radiation.. See rf dot11a-radio-profile and rf dot11g-radio-profile.

Example

The following command configures an ht-radio-profile named “default-g” and enables 40MHz-intolerance:

(host)[node](config) #rf ht-radio-profile default-g

40MHz-intolerance

Command History

Release

Modification

ArubaOS 8.4.0.0

The bss-color parameter was added.

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms, but operates with IEEEInstitute of Electrical and Electronics Engineers. 802.11n802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz. compliant devices only

Base operating system.

Config mode on Mobility Master.

/*]]>*/