You are here: Home > CLI Commands > Just_CLI_Topics > show ap arm client-match restriction-table

show ap arm client-match restriction-table

show ap arm client-match restriction-table

ap-name <name>

ip-addr <ipaddr>

ip6-addr <ip6-addr>

Description

If ClientMatch is enabled, the output of this command displays the list of clients that ClientMatch has restricted from the specified AP.

Syntax

Parameter

Description

ap-name <name>

Name of the AP for which you want to view the list of restricted clients

ip-addr <ipaddr>

IPv4 address of the AP for which you want to view the list of restricted clients

ip6-addr <ipaddr>

IPv6 address of the AP for which you want to view the list of restricted clients

Usage Guidelines

If ClientMatch is enabled, the managed devices send APs a list of clients that should not be allowed to associate to that AP. These lists of restricted clients help the client associate to the best AP, by preventing the client from associating with a sub-optional AP radio. The output of this command shows a list of all clients that were ever blacklisted from the specified AP.

Example

(host)[node] #show ap arm client-match restriction-table ap-name <ap-name>

Client Restriction Table for Wifi0

----------------------------------

Client MAC Time last restricted Restricted(Cur/Last)

---------- -------------------- --------------------

24:77:03:32:88:ec Wed Apr 10 03:51:00 2014 0

 

PS deauth Probe(home/scan/bc_ssid) Auth(home/scan)

--------- ------------------------ ---------------

- 2/0/no 4/0

 

Time since last restriction(sec) Radio Bssid

-------------------------------- -----------

18603 00:1a:1e:89:c0:d0

 

Client Restriction Table for Wifi1

----------------------------------

Client MAC Time last restricted Restricted(Cur/Last)

---------- -------------------- --------------------

24:77:03:32:7b:cc Wed Apr 10 03:47:16 2014 0

 

PS deauth Probe(home/scan/bc_ssid) Auth(home/scan)

--------- ------------------------ ---------------

0/0/no 0/0/no 0/0

 

Time since last restriction(sec) Radio Bssid

-------------------------------- -----------

3866 00:1a:1e:89:c0:c0

The output of this command includes the following parameters:

Parameter Description
Client MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network.

Displays the MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address of the client that Client Match is attempting to steer.

Time last restricted

Displays the date and time at which the client was last steered in the vicinity of this radio.

Restricted(Cur/Last)

A "1" in this field indicates that the client is currently in the process of being steered to another radio.

PS deauth

Displays if the client is in power save mode when client match is attempting to steer the client.

Probe(home/scan/bc_ssidService Set Identifier. SSID is a name given to a WLAN and is used by the client to access a WLAN network.)

Displays the number of probe requests received on home channel, AP scanning, and SSIDService Set Identifier. SSID is a name given to a WLAN and is used by the client to access a WLAN network. broadcast probe.

Auth(home/scan)

Displays the number of probe requests received on home channel and AP scanning for 802.11802.11 is an evolving family of specifications for wireless LANs developed by a working group of the Institute of Electrical and Electronics Engineers (IEEE). 802.11 standards use the Ethernet protocol and Carrier Sense Multiple Access with collision avoidance (CSMA/CA) for path sharing. authentication frames.

Time since last restricted

Display the time (in seconds) since the client was last steered in the vicinity of this radio.

Radio BssidBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly.

Displays the unique hard-wireless MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address of the AP. A unique BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly. applies to each frequency— 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. and 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network.—used from the AP.

Related Commands

Command

Description

rf arm-profile

This command enables ClientMatch.

show ap arm client-match probe-report

This command displays the client probe report for the specified AP.

show ap arm client-match neighbors

This command displays the BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly. of other APs seen by clients in the select AP's RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. neighborhood.

show ap arm virtual-beacon-report

This command displays the virtual beacon report for an AP with a specific IP or MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address.

show ap arm client-match unsupported

This command displays a list of clients that failed to be steered to a more optimal AP, and the reason the initial steering request was triggered.

show ap arm client-match summary

This command shows the history of AP association changes triggered by the client match feature.

show ap arm client-match history

This command shows the history of AP association changes triggered by the client match feature.

Command History

Release

Modification

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable or Config mode on Mobility Master.

/*]]>*/