You are here: Home > CLI Commands > Just_CLI_Topics > show ap arm neighbors

show ap arm neighbors

show ap arm neighbors {ap-name <ap-name>}|{bssid <bssid>}|{ip-addr <ip-addr>}

Description

Show the ARMAdaptive Radio Management. ARM dynamically monitors and adjusts the network to ensure that all users are allowed ready access. It enables full utilization of the available spectrum to support maximum number of users by intelligently choosing the best RF channel and transmit power for APs in their current RF environment. settings for an AP’s neighbors.

Syntax

Parameter

Description

ap-name <ap-name>

Show data for an AP with a specific name.

bssid <bssid>

Show data for a specific Basic Service Set Identifier (BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly.). An AP’s BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly. is usually the AP’s MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address.

ip-addr <ip-addr>

Show data for an AP with a specific IP address. Enter the IP address in dotted-decimal format.

Examples

The output of this command shows ARMAdaptive Radio Management. ARM dynamically monitors and adjusts the network to ensure that all users are allowed ready access. It enables full utilization of the available spectrum to support maximum number of users by intelligently choosing the best RF channel and transmit power for APs in their current RF environment. neighbor information for AP name ap70_1.

(host)[node]# show ap arm neighbors ap-name ap70_1

 

BSSID: BSSID of discovered radio ESSID: ESSID of discovered radio/Src BSSID through which the neighbor is discovered Channel: Channel of operation of discovered radio SNR: Signal to noise ratio of discovered radio tx-power: Tx Power of disovered radio (if known) PL: Path loss to discovered radio (using txpower and SNR) AP Flags: Active: Discovered using OTA updates Passive: Discovered using passive scan Indirect: Two hop neighbors discovered using neighbors OTA update Last Update: Timestamp when last OTA update was received (total OTA updates)

 

ARM Neighbors ------------- BSSID ESSID Channel SNR Tx-power PL (dB) AP Flags Last Update (Total updates) ----- ----- ------- --- -------- ------- -------- --------------------------- 6c:f3:7f:b6:68:14 ssid-ap1 153 49 22 69 Passive 18:64:72:93:6a:f2 ssid-ap2 132 48 24 68 Passive 18:64:72:02:24:30 ssid-ap3 153 47 18 63 Passive 18:64:72:01:f8:f0 ssid-ap4 36 60 22 0 Indirect 2015-03-12 16:38:26 9c:1c:12:fe:96:e4 ssid-ap5 11 33 18 123 Indirect 2015-03-13 08:37:18 6c:f3:7f:4b:64:23 ssid-ap6 6 51 20 125 Active 2015-03-12 14:05:48

The output of this command includes the following information:

Parameter

Description

BSSID

BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly. of the discovered radio of the AP.

ESSID

ESSIDExtended Service Set Identifier. ESSID refers to the ID used for identifying an extended service set. of the discovered radio of the AP or source BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly. through which the neighbor is discovered.

Channel

Channel of operation of the discovered radio of the AP.

SNR

Signal to noise ratio of the discovered radio of the AP.

Tx-power

Transmitter power of the discovered radio of the AP (if known).

PL (dB)

Path loss to the discovered radio (using tx-power and SNRSignal-to-Noise Ratio. SNR is used for comparing the level of a desired signal with the level of background noise.)

AP Flags

Active: Discovered using Over-The-Air (OTA) updates

Passive: Discovered using passive scan

Indirect: Two hop neighbors discovered using neighbors OTA update

Last Update

Time stamp when last OTA update was received (total OTA updates)

Related Commands

Command

Description

rf arm-profile

This command enables ClientMatch.

show ap arm client-match neighbors

This command displays the BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly. of other APs seen by clients in the select AP's RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. neighborhood.

Command History

Release

Modification

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable or Config mode on Mobility Master.

/*]]>*/