You are here: Home > CLI Commands > Just_CLI_Topics > show ap arm state

show ap arm state

show ap arm state [ap-name <ap-name>|dot11a|dot11g|ip-addr <ip-addr>]

Description

Display Adaptive Radio Management (ARMAdaptive Radio Management. ARM dynamically monitors and adjusts the network to ensure that all users are allowed ready access. It enables full utilization of the available spectrum to support maximum number of users by intelligently choosing the best RF channel and transmit power for APs in their current RF environment. ) information for an individual AP’s neighbors, or show all available data for any neighboring AP using an 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. or 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. radio type.

Syntax

Parameter

Description

ap-name <ap-name>

Show aggregate ARMAdaptive Radio Management. ARM dynamically monitors and adjusts the network to ensure that all users are allowed ready access. It enables full utilization of the available spectrum to support maximum number of users by intelligently choosing the best RF channel and transmit power for APs in their current RF environment. Neighbor Information for a specific AP.

dot11a

Show aggregate ARMAdaptive Radio Management. ARM dynamically monitors and adjusts the network to ensure that all users are allowed ready access. It enables full utilization of the available spectrum to support maximum number of users by intelligently choosing the best RF channel and transmit power for APs in their current RF environment. Neighbor Information for all APs using an 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. radio.

dot11g

Show aggregate ARMAdaptive Radio Management. ARM dynamically monitors and adjusts the network to ensure that all users are allowed ready access. It enables full utilization of the available spectrum to support maximum number of users by intelligently choosing the best RF channel and transmit power for APs in their current RF environment. Neighbor Information for all APs using an 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. radio.

ip-addr <ip-addr>

Show aggregate ARMAdaptive Radio Management. ARM dynamically monitors and adjusts the network to ensure that all users are allowed ready access. It enables full utilization of the available spectrum to support maximum number of users by intelligently choosing the best RF channel and transmit power for APs in their current RF environment. Neighbor Information for a AP with a specific IP address by entering its IP address in dotted-decimal format.

Usage Guidelines

The output of the show ap arm state command shows 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. and 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. information for all APs. Include an AP name or IP address to show data for just a single AP, or use the dot11a or dot11g keywords to show data for all APs using that radio type.

Examples

The output of this command shows 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. information for all neighboring APs.

(host)[node]# show ap arm state

 

show ap arm state ap-name AP49

AP-1249:10.100.139.233:52:21:26-Edge:disable : Client Density:13

Neighbor Data

-------------

Name IP Address SNR Assignment Neighbor Density

---- ---------- --- ---------- ----------------

AP42 10.100.139.249 41 52/21 13/17/100/76

AP09 10.100.139.224 22 56/21 3/5/23/60

AP48 10.100.139.241 36 60/21 9/11/69/81

The output of this command includes the following information:

Column

Description

Name

Name of an AP.

IP address

IP address of an AP.

SNR

Signal-to-noise (SNRSignal-to-Noise Ratio. SNR is used for comparing the level of a desired signal with the level of background noise.) ratio. SNRSignal-to-Noise Ratio. SNR is used for comparing the level of a desired signal with the level of background noise. is the power ratio between an information signal and the level of background noise.

Assignment

The AP’s current channel assignment.

Neighbor Density

The neighborhood density for the specified AP is listed with the values A/B/C/D, where:

A= Number of the AP’s clients heard in the AP neighbor’s client list

B= Number of clients in AP neighbor’s client list

C= Density percentage, (AP clients heard in in the AP neighbor client list / AP client density * 100).

D= Density Percentage (AP clients heard in the AP neighbor’s client list / neighbor client density * 100)

Related Commands

Command

Description

rf arm-profile

This command enables ClientMatch.

Command History

Release

Modification

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable or Config mode on Mobility Master.

/*]]>*/