You are here: Home > CLI Commands > Just_CLI_Topics > show ap debug datapath

show ap debug datapath

show ap debug datapath {ap-group <ap-group>|ap-name <ap-name>|bssid <bssid>|ip-addr <ip-addr>|ip6-addr <ip6-addr>}

Description

Show datapath tunnel parameters of an AP or AP group.

Syntax

Parameter

Description

ap-group <ap-group>

Show data path information for a specific AP group.

ap-name <ap-name>

Show data path information for an AP with a specific name.

bssid <bssid>

Show data path information for a specific Basic Service Set Identifier (BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly.). The Basic Service Set Identifier (BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly.) is usually the AP’s MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address.

ip-addr <ip-addr>

Show data path information for an AP with a specific IP address by entering an IP address in dotted-decimal format.

ip6-addr <ip6-addr>

Show data path information for an AP with a specific IPv6 address by entering an IP address in dotted-decimal format.

Example

The output of the following command shows datapath tunnel parameters for an AP with the IP address 192.0.2.32.

(host) #show ap debug datapath ip-addr 192.0.2.32

 

Datapath Parameters Table

-------------------------

essid encr-alg client-vlan-id tunnel-id gre-type deny-bcast num-clients

----- -------- -------------- --------- -------- ---------- -----------

guest Open 63 0x10f6 0x8300 disable 0

voip WPA2 8021X AES 66 0x1103 0x8310 disable 7

corp WPA2 PSK AES 66 0x10f1 0x8320 disable 0

guest Open 63 0x10f7 0x8200 disable 1

wpa2 WPA2 8021X AES 65 0x10be 0x8210 enable 15

The output of this command includes the following information:

Column

Description

ESSID

The Extended Service Set Identifier is a unique name that identifies a wireless network

encr-alg

Encryption algorithm used by the network

client-vlan-id

ID of the network VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN.

tunnel-id

Identification number of the AP’s tunnel.

gre-type

GREGeneric Routing Encapsulation. GRE is an IP encapsulation protocol that is used to transport packets over a network. tunnel type.

deny-bcast

If enabled, the AP will respond to broadcast probe requests. If disabled, the AP will not respond to these requests.

num-clients

Number of clients currently using the network.

The output of the following command shows datapath tunnel parameters for an AP with the IPv6 address 11:12:11:11::2.

(host) #show ap debug datapath ip6-addr 11:12:11:11::2

Datapath Parameters Table

-------------------------

essid encr-alg client-vlan-id tunnel-id gre-type deny-bcast num-clients

----- -------- -------------- --------- -------- ---------- -----------

i-platform-mobility WPA2 PSK AES 10 0x1000b 0x8300 disable 0

i-platform-mobility WPA2 PSK AES 10 0x1000a 0x8200 disable 1

Command History

Command

Description

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable or Config mode on Mobility Master.

/*]]>*/