You are here: Home > CLI Commands > Just_CLI_Topics > show ap remote debug mgmt-frames

show ap remote debug mgmt-frames

show ap remote debug mgmt-frames {ap-name <ap-name>}|{ip-addr <ip-addr>}|{ip6-addr <ip6-addr>} [client-mac <client-mac>] [count <count>]

Description

This command shows traced 802.11802.11 is an evolving family of specifications for wireless LANs developed by a working group of the Institute of Electrical and Electronics Engineers (IEEE). 802.11 standards use the Ethernet protocol and Carrier Sense Multiple Access with collision avoidance (CSMA/CA) for path sharing. management frames for a remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link..

Syntax

Parameter

Description

Range

ap-name <ap-name>

Show debugging information for a specific AP.

ip-addr <ip-addr>

Show debugging information for an AP with a specific IP address by entering its IP address in dotted-decimal format.

ip6-addr <ip6-addr>

Show debugging information for an AP with a specific IPv6 address by entering its IPv6 address in dotted-decimal format.

client-mac <client-mac>

Show the AP associations for a specific MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address by entering the MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address of the client.

count <count>

Limit the amount of information displayed by specifying number of frames to appear in the output of this command.

1–128

Usage Guidelines

The optional output modifiers | begin , | exclude, and | include help you display those lines that begin, include, exclude, respectively, the line expression given in the CLICommand-Line Interface. A console interface with a command line shell that allows users to execute text input as commands and convert these commands to appropriate functions. command. The | redirect-output modifier helps you redirect the command output.

Examples

Use this command to debug 802.1 authentication on a remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link.. The example below shows that a client successfully associated with the remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link., then was later deauthenticated.

(host) [mynode] #show ap remote debug mgmt-frames ap-name AP32

 

The output of this command includes the following information:

Column

Description

Timestamp

The time the management frame was sent.

stype

One of the following 802.11802.11 is an evolving family of specifications for wireless LANs developed by a working group of the Institute of Electrical and Electronics Engineers (IEEE). 802.11 standards use the Ethernet protocol and Carrier Sense Multiple Access with collision avoidance (CSMA/CA) for path sharing. frame types:

auth: Authorization frame

deauth: Deauthorization frame

assoc-resp: Association response

assoc-req: Association request

SA

Source MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address.

DA

Destination MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address.

BSS

BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly. of the AP.

signal

Signal strength as a signal to noise ratio. For example, a value of 30 would indicate that the power of the received signal is 30 dBmDecibel-Milliwatts. dBm is a logarithmic measurement (integer) that is typically used in place of mW to represent receive-power level. AMP normalizes all signals to dBm, so that it is easy to evaluate performance between various vendors. above the signal noise threshold.

Misc

Additional information describing the client’s action. In the case of deauthentication, a reason associated with the event will be displayed in this column.

Command History

Release

Modification

ArubaOS 8.2.0.0

The ip6-addr parameter was added.

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms

Base operating system.

Enable or Config mode on the managed device or controller where the AP terminates.

/*]]>*/