You are here: Home > CLI Commands > Just_CLI_Topics > show ap debug system-status

show ap debug system-status

show ap debug system-status

ap-name <ap-name>

bssid <bssid>

ip-addr <ip-addr>

ip6-addr <ip6-addr>

Description

Show detailed system status information for an AP.

Syntax

Parameter

Description

ap-name <ap-name>

Show system status data for an AP with a specific name.

bssid <bssid>

Show system status data for a specific Basic Service Set Identifier (BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly.) on an AP. The Basic Service Set Identifier (BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly.) is usually the AP’s MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address.

ip-addr <ip-addr>

Show system status data for an AP with a specific IP address by entering an IP address in dotted-decimal format.

ip6-addr <ip6-addr>

Show system status data for an AP with a specific IPv6 address by entering an IPv6 address in dotted-decimal format.

Usage Guidelines

Issue this command under the guidance of Aruba technical support to troubleshoot network issues. The output of this command displays the following types of information (if it exists) for the selected AP:

Bootstrap information

Per-radio statistics

EthernetEthernet is a network protocol for data transmission over LAN. duplex/speed settings

Descriptor Usage

Encryption statistics

Tunnel heartbeat stats

Interface counters

AP uptime

Boot version

MTUMaximum Transmission Unit. MTU is the largest size packet or frame specified in octets (eight-bit bytes) that can be sent in networks such as the Internet. discovery

Memory usage

LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. information

ARPAddress Resolution Protocol. ARP is used for mapping IP network address to the hardware MAC address of a device. cache

Kernel slab statistics

Power status

Route table

Interrupts

CPUCentral Processing Unit. A CPU is an electronic circuitry in a computer for processing instructions. type

Interface Information

Crash Information

CPUCentral Processing Unit. A CPU is an electronic circuitry in a computer for processing instructions. usage statistics

System Status Script

Radio profile name

Dual 5 GHzGigahertz. mode

Power Status

The following lines under power status indicate the power status of the AP:

Operational State indicates the current state of the AP, that is, as seen with the power light on the AP. Operational State may be different from Current HW State as a result of LLDPLink Layer Discovery Protocol. LLDP is a vendor-neutral link layer protocol in the Internet Protocol suite used by network devices for advertising their identity, capabilities, and neighbors on an IEEE 802 local area network, which is principally a wired Ethernet. negotiation.

Current HW State indicates the result from POE negotiation in hardware.

LLDP Negotiated POE Power indicates the LLDPLink Layer Discovery Protocol. LLDP is a vendor-neutral link layer protocol in the Internet Protocol suite used by network devices for advertising their identity, capabilities, and neighbors on an IEEE 802 local area network, which is principally a wired Ethernet. negotiated power.

The following parameters are included in the output of this command, and can help troubleshoot problems on an AP or wireless network.

Parameter

Description

The Failed column in the Descriptor Usage section

This parameter can tell you if the AP is dropping packets.

Interface Information table

This parameter can tell you if the EthernetEthernet is a network protocol for data transmission over LAN. network is working properly. This table should not show an excessive number of errors.

AP Uptime table

Low values in this table can indicate problems with the wired network, or with the AP itself.

Tunnel Heartbeat table

This table can indicate the health of the underlying wired network.

Rebootstrap Information table /Reboot Information table

A large number of reboots can mean that the AP has hardware problems.

Command History

Command

Description

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable or Config mode on Mobility Master.

/*]]>*/