You are here: Home > CLI Commands > Just_CLI_Topics > show ap debug ble-table

show ap debug ble-table

show ap debug ble-table {ap-name <ap-name>|ip-addr <ip-addr>|ip6-addr <ip6-addr>}

Description

This command displays the statistics for BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. devices seen by the AP. In addition, the command displays beacons seen by the APB, each of the beacons' attributes such as the Major-Minor numbers, Batter Level, Firmware version, time since the beacon was last heard by the APB.

 

This command is supported in 210 Series, 220 Series (with external BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices. ), and 320 Series.

Syntax

Parameter

Description

ap-name

Displays the statistics for the BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. devices seen by the AP for a specific AP based on the AP name.

ip-addr

Displays the statistics for the BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. devices seen by the AP for a specific AP based on the IPv4 address.

ip6-addr

Displays the statistics for the BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. devices seen by the AP for a specific AP based on the IPv6 address.

Example

The output of this command displays the statistics for BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. devices seen by the AP.

(host) #show ap debug ble-table ap-name ap325

 

BLE Device Table

----------------

MAC HW_Type FW_Ver Flags Status Batt(%) RSSI Major# Minor#

--- ------- ------ ----- ------ ------- ---- ------ ------

d0:39:72:d5:43:75 LS-BT1 OAD A 1.1-25 0x0001 IAH 100 -71 1000 1215

c4:be:84:19:8b:a3 LS-BT1USB OAD B 1.1-25 0x0003 IAH USB -83 0 0

c4:be:84:19:ec:67 OCTOMORE OAD B 1.1-26 0x0003 IAH -- -74 0 0

c4:be:84:19:ef:99 OCTOMORE OAD B 1.1-38 0x0083 LIA -- -- 1000 1374

78:a5:04:15:23:35 LS-BT1 OAD A 1.1-25 0x0001 IAH 100 -79 1000 1222

c4:be:84:19:ec:2f OCTOMORE OAD B 1.1-26 0x0003 IAH -- -83 0 0

 

UUID Tx_Power Last Update Uptime

---- -------- ----------- ------

5D3BCC63-BD6B-4FAF-906F-91C91519A69B 13 8s 11h:3m:0s

4152554E-F99B-4A3B-86D0-947070693A78 14 4s 23h:51m:30s

4152554E-F99B-4A3B-86D0-947070693A78 14 0s 19h:38m:30s

09458C20-4586-4ED3-8D2F-A0842ACBD6E6 2 4s 18h:45m:0s

09458C20-4586-4ED3-8D2F-A0842ACBD6E6 13 0s 22h:36m:0s

4152554E-F99B-4A3B-86D0-947070693A78 14 0s 19h:39m:0s

 

Total beacons:6

APB UI:[0/NO_UPGRADE_REQD]:65535(0xffff) blks:0/0 rep:0 total:0(0x0)

APB UI:upg_b_status-next:0x00/ooo:0x00/next2:0x00/upg_b:0x00/allrx:0x00/oooBlk:0x00/oooBlk:0x00/oooBlk:0x00

APB UI:upg_b_status_errs-inv_upg:0x00/inv_cmd:0x00/inv_op:0x00/buf_tl:0x00/good:0x00

APB UI:acks/ka-From APB:0x00/0x00 From app:0x00,0x00/0x00

APB UI Clock:Start:1969-12-31 16:00:00 End:1969-12-31 16:00:00 Current:2015-10-27 11:48:20

Note: Battery level for LS-BT1USB devices is indicated as USB.

Note: Uptime is shown as Days hour:minute:second.

Note: Last Update is time in seconds since last heard update.

Status Flags:L:AP's local beacon; I:iBeacon; A: Aruba Beacon; H: Aruba HiPower Beacon

:U:Image Upgrade Pending

Command History

Command

Description

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable or Config mode on Mobility Master.

/*]]>*/