You are here: Home > CLI Commands > Just_CLI_Topics > show ap ht-rates

show ap ht-rates

show ap ht-rates bssid <bssid>

Description

Show high-throughput rate information for a basic service set (BSSBasic Service Set. A BSS is a set of interconnected stations that can communicate with each other. BSS can be an independent BSS or infrastructure BSS. An independent BSS is an ad hoc network that does not include APs, whereas the infrastructure BSS consists of an AP and all its associated clients. ).

Syntax

Parameter

Description

bssid <bssid>

Show data for a specific Basic Service Set Identifier (BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly.) on an AP. An AP’s BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly. is usually the AP’s MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address.

Examples

The output of this command shows high-throughput rates for each supported MCSModulation and Coding Scheme. MCS is used as a parameter to determine the data rate of a wireless connection for high throughput. value. These values are applicable to high-throughput (802.11n802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz.-capable) APs only.

(host) [mynode] #show ap ht-rates bssid 00:1a:1e:1e:5a:10

 

AP "AL12" Radio 0 BSSID 00:1a:1e:1e:5a:10 High-throughput Rates (Mbps)

----------------------------------------------------------------------

MCS Streams 20 MHz 40 MHz 40 MHz SGI

--- ------- ------ ------ ----------

0 1 6.5 13.5 15.0

1 1 13.0 27.0 30.0

2 1 19.5 40.5 45.0

3 1 26.0 54.0 60.0

4 1 39.0 81.0 90.0

5 1 52.0 108.0 120.0

6 1 58.5 121.5 135.0

7 1 65.0 135.0 150.0

8 2 13.0 27.0 30.0

9 2 26.0 54.0 60.0

10 2 39.0 81.0 90.0

11 2 52.0 108.0 120.0

12 2 78.0 162.0 180.0

13 2 104.0 216.0 240.0

14 2 117.0 243.0 270.0

15 2 130.0 270.0 300.0

The output of this command includes the following information:

Column

Description

MCS

A Modulation Coding Scheme (MCSModulation and Coding Scheme. MCS is used as a parameter to determine the data rate of a wireless connection for high throughput.) values supported on this high-throughput SSIDService Set Identifier. SSID is a name given to a WLAN and is used by the client to access a WLAN network..

Streams

Number of spatial streams used by the MCSModulation and Coding Scheme. MCS is used as a parameter to determine the data rate of a wireless connection for high throughput. index value.

20 MHz

802.11n802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz. data rates for the MCSModulation and Coding Scheme. MCS is used as a parameter to determine the data rate of a wireless connection for high throughput. for 20 Mhz transmissions.

40 MHz

802.11n802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz. data rates for the MCSModulation and Coding Scheme. MCS is used as a parameter to determine the data rate of a wireless connection for high throughput. for 40 Mhz transmissions.

40 MHz SGI

802.11n802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz. data rates for the MCSModulation and Coding Scheme. MCS is used as a parameter to determine the data rate of a wireless connection for high throughput. for 40 Mhz transmissions using a short guard interval.

Related Commands

Command

Description

show ap vht-rates

Show very-high-throughput rate information for a basic service set (BSSBasic Service Set. A BSS is a set of interconnected stations that can communicate with each other. BSS can be an independent BSS or infrastructure BSS. An independent BSS is an ad hoc network that does not include APs, whereas the infrastructure BSS consists of an AP and all its associated clients. ).

Command History

Version

Modification

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable mode on Mobility Master.

/*]]>*/