You are here: Home > CLI Commands > Just_CLI_Topics > show ap monitor stats

show ap monitor stats

show ap monitor stats advanced {ap-name <ap-name>}|{bssid <bssid>}|{ip-addr <ip-addr>}|{ip6-addr <ip6-addr>} client-mac <client-mac>

 

show ap monitor stats {ap-name <ap-name>}|{bssid <bssid>}|{ip-addr <ip-addr>}||{ip6-addr <ip6-addr>} mac <mac> <verbose>

Description

Show packet, signal and channel statistics for an AP or a client.

Syntax

Parameter

Description

advanced

Show advanced statistics for an AP or client.

ap-name <ap-name>

Show statistics for an AP with a specific name.

bssid <bssid>

Show data for a specific Basic Service Set Identifier (BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly.) on an AP. The Basic Service Set Identifier (BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly.) is usually the AP’s MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address.

ip-addr <ip-addr>

Show data for an AP with a specific IP address by entering its IP address in dotted-decimal format.

ip6-addr <ip6-addr>

Show data for an AP with a specific IPv6 address by entering its IPv6 address in dotted-decimal format.

mac <mac>

Show data for a specific MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address by entering the MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address of a client or AP.

client-mac <client-mac>

Show data for a specific client MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address by entering the MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address of a client.

verbose

Enable verbose mode to display the statistics of an AP.

Example

The output of the following command shows monitoring statistics for the AP ap305, and a client with the MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address d8:6c:02:99:bc:7a.

(host) #show ap monitor stats ap-name ap305 mac d8:6c:02:99:bc:7a verbose

 

Aggregate Stats

---------------

retry low-speed non-unicast recv-error frag bwidth

----- --------- ----------- ---------- ---- ------

0 0 0 0 0 0

RSSI

----

avg-signal low-signal high-signal count duration (sec)

---------- ---------- ----------- ----- --------------

51 51 51 4 50

Monitored Time:6626

Last Packet Time:585500

Uptime:585502

 

 

AMPDU Tx Stats

---------------

tx-non-ampdu-pkt tx-ampdu-pkt tx-filtered-pkt tx-ampdu-byte ---------------- ------------ --------------- ------------- 0 0 0 0

tx-filtered-bytes tx-first-pkt tx-middle-pkt tx-last-pkt

----------------- ------------ ------------- -----------

0 0 0 0

AMPDU Rx Stats

---------------

tx-non-ampdu-pkt tx-ampdu-pkt tx-filtered-pkt tx-ampdu-byte ---------------- ------------ --------------- ------------- 0 7 66 73102

tx-filtered-bytes tx-first-pkt tx-middle-pkt tx-last-pkt

----------------- ------------ ------------- -----------

66639 0 0 7

 

DoS Frames

----------

tx old-tx rx old-rx

-- ------ -- ------

0 0 0 0

Interference Baseline

---------------------

FRR FRER

--- ----

17 4

Handoff Assist

--------------

rssi-index cur-signal old-cur-signal

---------- ---------- --------------

0 51 0

High Throughput Parameters

--------------------------

ht-type primary-channel sec-channel gf-supported 40mhz-intolerance

------- --------------- ----------- ------------ -----------------

none 0 0 0 0

 

The output of this command includes the following information:

Column

Description

retry

Percent of 802.11802.11 is an evolving family of specifications for wireless LANs developed by a working group of the Institute of Electrical and Electronics Engineers (IEEE). 802.11 standards use the Ethernet protocol and Carrier Sense Multiple Access with collision avoidance (CSMA/CA) for path sharing. retry frames sent because a client failed to send an ACK.

Low-speed

Percent of frames sent at a data rate of 18 MbpsMegabits per second or slower.

non-unicast

Percent of non-unicast frames

recev-error

Percent of error frames of all frames seen in the last second.

frag

Rate of fragmented packets, in frames per second

bwth

Current bandwidth, in bps.

avg-signal

Average signal-to-noise ratio over the interval since the AP’s last reset.

Low-signal

Lowest signal-to-noise ratio over the interval since the AP’s last reset.

high-signal

Highest signal-to-noise ratio over the interval since the AP’s last reset.

count

Number of packets seen on the AP over the interval since the AP’s last reset.

Duration

Time over which the AP has measured RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values. values.

tx

The total number of deauthorization frames sent to this MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address for containment in the interval from the AP’s last reset until the current timer tick.

old-tx

The total number of deauthorization frames sent to this MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address for containment until the previous timer tick.

rx

The total number of deauthorization frames spoofing the MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address in the interval from the AP’s last reset until the current timer tick.

old-rx

The total number of deauthorization frames sent to this MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address for containment until the previous timer tick.

FRR

Frame retry rate, in frames per second.

FRER

Frame error retry rate, in frames per second.

rssi-index

This value indicates the number of consecutive timer ticks over which the value of the Receive Signal Strength Indicator (RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values.) of the client has reduced by more than 3 units.

NOTE: This value is updated only if 'handoff-assist' is enabled in the AP’s RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. Optimization profile.

cur-signal

The Receive Signal Strength Indicator (RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values.) of the most recent frame received from the specified MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address.

old-cur-signal

The most recent Receive Signal Strength Indicator (RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values.) of the MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. which is 3 lower or 5 higher than the current RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values..

NOTE: This value is updated only if 'handoff-assist' is enabled in the AP’s RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. Optimization profile

ht-type

This parameter indicates support for the following HTHigh Throughput. IEEE 802.11n is an HT WLAN standard that aims to achieve physical data rates of close to 600 Mbps on the 2.4 GHz and 5 GHz bands. types:

no: No support for high-throughput.

HT-20: Support for 20 Mhz high-throughput only.

HT-40: Support for 40 Mhz high-throughput.

primary-channel

Primary radio channel.

sec-channel

Secondary radio channel

gf-supported

If 1, this AP supports greenfield mode. If 0, greenfield is not supported.

40mhz-intolerance

Indicates whether the specified MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address is 40 Mhz intolerant.

Related Commands

Command

Description

show ap monitor debug

This command shows information for an Air Monitor’s current status, message counters, or profile settings.

show ap monitor

This command shows information for Aruba Air Monitors.

Command History

Command

Description

ArubaOS 8.4.0.0

The output of the show ap monitor stats command was modified to display the additional debug counter information.

ArubaOS 8.2.0.0

The ip6-addr parameter was added.

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable or Config mode on Mobility Master.

/*]]>*/