You are here: Home > CLI Commands > Just_CLI_Topics > show ap provisioning

show ap provisioning

show ap provisioning {ap-name <ap-name>}|{bssid <bssid>}|{ip-addr <ip-addr>}

Description

Show provisioning parameters currently used by an AP.

Syntax

Parameter

Description

ap-name <ap-name>

Show data for an AP with a specific name.

bssid <bssid>

Show data for a specific Basic Service Set Identifier (BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly.) on an AP. An AP’s BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly. is usually the AP’s MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address.

ip-addr <ip-addr>

Show data for an AP with a specific IP address.

Example

The output of this command shows that the AP named AP8 has mostly default parameters. These appear with the value N/A.

(host) #show ap provisioning ap-name AP8

AP "mp2" Provisioning Parameters

--------------------------------

Item Value

---- -----

 

(host) (config) #show ap provisioning ap-name 00:24:6c:c7:d5:c8

 

AP "00:24:6c:c7:d5:c8" Provisioning Parameters

----------------------------------------------

Item Value

---- -----

AP Name 00:24:6c:c7:d5:c8

AP Group default

Location name N/A

SNMP sysLocation N/A

Master 10.4.62.9

Gateway N/A

IPv6 Gateway N/A

Netmask N/A

IP Addr N/A

IPv6 Addr N/A

IPv6 Prefix 64

DNS IP N/A

DNS IPv6 N/A

Domain Name N/A

Server Name aruba-master

Server IP 10.4.62.9

Antenna gain for 802.11a N/A

Antenna gain for 802.11g N/A

Antenna for 802.11a both

Antenna for 802.11g both

Single chain mode for Radio 0 0

Single chain mode for Radio 1 0

IKE PSK N/A

PAP User Name N/A

PAP Password N/A

PPPOE User Name N/A

PPPOE Password N/A

PPPOE Service Name N/A

PPPOE CHAP Secret N/A

USB User Name N/A

USB Password N/A

USB Device Type any

...

...

...

The output of this command includes the following information:

Column

Description

AP Name

Name of the AP.

AP Group

AP group to which the AP belongs.

Location name

Fully-qualified location name (FQLNFully Qualified Location Name. FQLN is a device location identifier in the format: APname.Floor.Building.Campus.) for the AP.

SNMP sysLocation

User-defined description of the location of the AP, as defined with the command provision-ap syslocation.

Master

Name or IP address for Mobility Master.

Gateway

IP address of the default gatewayGateway is a network node that allows traffic to flow in and out of the network. for the AP.

Netmask

NetmaskNetmask is a 32-bit mask used for segregating IP address into subnets. Netmask defines the class and range of IP addresses. for the AP’s IP address.

IP Addr

IP address for the AP.

IPv6

The static IP6 address of the AP.6

IPv6 Prefix

The prefix of static IPv6 address of the AP.

Dns IP

IP address of the DNSDomain Name System. A DNS server functions as a phone book for the intranet and Internet users. It converts human-readable computer host names into IP addresses and IP addresses into host names. It stores several records for a domain name such as an address 'A' record, name server (NS), and mail exchanger (MX) records. The Address 'A' record is the most important record that is stored in a DNS server, because it provides the required IP address for a network peripheral or element. server.

DNS IPv6

The prefix of static IPv6 address of the AP.

Domain Name

Domain name used by the AP.

Server Name

DNSDomain Name System. A DNS server functions as a phone book for the intranet and Internet users. It converts human-readable computer host names into IP addresses and IP addresses into host names. It stores several records for a domain name such as an address 'A' record, name server (NS), and mail exchanger (MX) records. The Address 'A' record is the most important record that is stored in a DNS server, because it provides the required IP address for a network peripheral or element. name of the managed device from which the AP boots.

Server IP

IP address of the managed device from which the AP boots

Antenna gain for 802.11a

Antenna gain for 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. (5GHz) antenna.

Antenna gain for 802.11g

Antenna gain for 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. (2.4GHz) antenna.

Antenna for 802.11a

Antenna use for 5 GHzGigahertz. (802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps.) frequency bandBand refers to a specified range of frequencies of electromagnetic radiation..

1: AP uses antenna 1

2: AP uses antenna 2

both: AP uses both antennas

Antenna for 802.11g

Antenna use for 2.4 GHzGigahertz. (802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network.) frequency bandBand refers to a specified range of frequencies of electromagnetic radiation..

1: AP uses antenna 1

2: AP uses antenna 2

both: AP uses both antennas

Single chain mode for Radio 0

If this parameter is set to 1 for an 802.11n802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz.-capable radio, the radio will operate in single-chain mode, and will transmit and receive data using only legacy rates and single-stream HTHigh Throughput. IEEE 802.11n is an HT WLAN standard that aims to achieve physical data rates of close to 600 Mbps on the 2.4 GHz and 5 GHz bands. rates up to MCSModulation and Coding Scheme. MCS is used as a parameter to determine the data rate of a wireless connection for high throughput. 7. This parameter is set to 0 (disabled) by default.

Single chain mode for Radio 1

If this parameter is set to 1 for an 802.11n802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz.-capable radio, the radio will operate in single-chain mode, and will transmit and receive data using only legacy rates and single-stream HTHigh Throughput. IEEE 802.11n is an HT WLAN standard that aims to achieve physical data rates of close to 600 Mbps on the 2.4 GHz and 5 GHz bands. rates up to MCSModulation and Coding Scheme. MCS is used as a parameter to determine the data rate of a wireless connection for high throughput. 7. This parameter is set to 0 (disabled) by default.

IKE PSK

IKEInternet Key Exchange. IKE is a key management protocol used with IPsec protocol to establish a secure communication channel. IKE provides additional feature, flexibility, and ease of configuration for IPsec standard. PSKPre-shared key. A unique shared secret that was previously shared between two parties by using a secure channel. This is used with WPA security, which requires the owner of a network to provide a passphrase to users for network access. The IKEInternet Key Exchange. IKE is a key management protocol used with IPsec protocol to establish a secure communication channel. IKE provides additional feature, flexibility, and ease of configuration for IPsec standard. pre-shared key.

PAP password

Password Authentication Protocol (PAPPassword Authentication Protocol. PAP validates users by password. PAP does not encrypt passwords for transmission and is thus considered insecure.) password for the AP.

PAP User Name

PAPPassword Authentication Protocol. PAP validates users by password. PAP does not encrypt passwords for transmission and is thus considered insecure. username for the AP.

PPPOE User Name

Point-to-Point Protocol over EthernetEthernet is a network protocol for data transmission over LAN. (PPPoEPoint-to-Point Protocol over Ethernet. PPPoE is a method of connecting to the Internet, typically used with DSL services, where the client connects to the DSL modem.) user name for the AP.

PPPOE Password

PPPoEPoint-to-Point Protocol over Ethernet. PPPoE is a method of connecting to the Internet, typically used with DSL services, where the client connects to the DSL modem. password for the AP.

PPPOE Service Name

PPPoEPoint-to-Point Protocol over Ethernet. PPPoE is a method of connecting to the Internet, typically used with DSL services, where the client connects to the DSL modem. service name for the AP.

PPPOE CHAP secret

PPPoEPoint-to-Point Protocol over Ethernet. PPPoE is a method of connecting to the Internet, typically used with DSL services, where the client connects to the DSL modem. CHAPChallenge Handshake Authentication Protocol. CHAP is an authentication scheme used by PPP servers to validate the identity of remote clients. secret key for the AP.

USB User Name

The PPPPoint-to-Point Protocol. PPP is a data link (layer 2) protocol used to establish a direct connection between two nodes. It can provide connection authentication, transmission encryption, and compression. username provided by the cellular service provider

USB Password

A PPPPoint-to-Point Protocol. PPP is a data link (layer 2) protocol used to establish a direct connection between two nodes. It can provide connection authentication, transmission encryption, and compression. password, if provided by the cellular service provider

USB Type

The USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices. driver type.

USB Device Identifier

The USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices. device identifier.

USB Dial String

The dial string for the USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices. modem. This parameter only needs to be specified if the default string is not correct.

USB Initialization String

The initialization string for the USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices. modem. This parameter only needs to be specified if the default string is not correct.

USB TTY device data path

The TTYTeleTypeWriter. TTY-enabled devices allow telephones to transmit text communications for people who are deaf or hard of hearing as well as transmit voice communication. device path for the USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices. modem. This parameter only needs to be specified if the default path is not correct.

USB TTY device control path

The TTYTeleTypeWriter. TTY-enabled devices allow telephones to transmit text communications for people who are deaf or hard of hearing as well as transmit voice communication. device control path for the USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices. modem. This parameter only needs to be specified if the default path is not correct.

Uplink VLAN

If you configured an uplink VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. on an AP connected to a port in trunk mode, the AP sends and receives frames tagged with this VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. on its EthernetEthernet is a network protocol for data transmission over LAN. uplink.

By default, an AP has an uplink vlanVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. of 0, which disables this feature.

Link Priority Ethernet

Set the priority of the wired uplink, from 0-255. Each uplink type has an associated priority; wired ports having the highest priority by default.

Link Priority Cellular

The priority of the cellular uplink, from 0-255. By default, the cellular uplink is a lower priority than the wired uplink; making the wired link the primary link and the cellular link the secondary or backup link.

Mesh Role

If the mesh role is “none,” the AP is operating as a thin AP. An AP operating as a mesh node can have one of two roles: mesh portal or mesh point.

Installation

Indicates the type of installation (indoor or outdoor). The default parameter indicates that the installation mode is determined by the AP model type.

Latitude

Latitude coordinates of the AP, in the format Degrees Minutes Seconds (DMS).

Longitude

Longitude coordinates of the AP, in the format Degrees Minutes Seconds (DMS).

Altitude

Altitude, in meters, of the AP. This parameter is supported on outdoor APs

only.

Antenna bearing for 802.11a

Horizontal coverage distance of the 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. (5GHz) antenna from true north, from 0-360 degrees.

NOTE: This parameter is supported on outdoor APs only. The horizontal coverage pattern does not consider the elevation or vertical antenna pattern.

Antenna bearing for 802.11g

Horizontal coverage distance of the 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. (2.4GHz) antenna from true north, from 0-360 degrees.

NOTE: This parameter is supported on outdoor APs only. The horizontal coverage pattern does not consider the elevation or vertical antenna pattern.

Antenna tilt angle for 802.11a

The angle of the 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. (5GHz) antenna. This parameter can range from between -90 degrees and 0 degrees for downtilt, and between +90 degrees and 0 degrees for uptilt.

Antenna tilt angle for 802.11g

The angle of the 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. (2.4GHz) antenna. This parameter can range from between -90 degrees and 0 degrees for downtilt, and between +90 degrees and 0 degrees for uptilt.

Mesh SAE

Shows if the AP has enabled or disabled Secure Attribute Exchange (SAE) on a mesh network.

Related Commands

Command

Description

provision-ap

Change provisioning parameters for an individual AP. This command does not save the provisioning parameters settings in a reusable profile.

ap provisioning-profile

This command defines a provisioning profile for an AP or group of APs.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable or Config mode on Mobility Master.

/*]]>*/