You are here: Home > CLI Commands > Just_CLI_Topics > show ap radio-database

show ap radio-database

show ap radio-database [band a|g] [group <group>] [mode access-point|air-monitor|disabled|ht|ht-40mhz|legacy|sap-monitor] [sort-by ap-group|ap-ip|ap-name|ap-type|switch-ip] [sort-direction ascending|descending] [start <start>] [switch <switch-ip-addr>]

Description

Show radio information for Access Points visible to this controller.

Syntax

Parameter

Description

band

Show only APs with a radio operating in the specified bandBand refers to a specified range of frequencies of electromagnetic radiation..

a

Show only APs with a radio operating in the 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. bandBand refers to a specified range of frequencies of electromagnetic radiation. (5 GHzGigahertz.).

g

Show only APs with a radio operating in the 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. bandBand refers to a specified range of frequencies of electromagnetic radiation. (2.4 GHzGigahertz.).

group <group>

Show only APs associated with the specified AP group.

mode

Show only APs with a radio operating in the specified mode.

access-point

Show only APs operating as access points.

air-monitor

Show only APs operating as air monitors.

disabled

Show only disabled APs.

ht

Show only high-throughput APs.

ht-40mhz

Show only 40 Mhz high-throughput APs.

legacy

Show only legacy (not high-throughput) APs.

sap-monitor

Show only APs operating as SAP monitors.

sort-by

Sort the output of this command by a specific data column.

ap-group

Sort the output of this command by AP group name.

ap-ip

Sort the output of this command by AP IP address.

ap-name

Sort the output of this command by AP name.

ap-type

Sort the output of this command by AP model type.

switch-ip

Sort the output of this command by controller ip address.

sort-direction

Select a sort direction for the output of this command.

ascending

Sort the output in ascending order.

descending

Sort the output in descending order.

start

Start displaying the output of this command at a chosen index number by entering the index number of the AP at which command output should start.

switch <switch-ip-addr>

Display information for APs associated with a specific controller by entering the IP address of that controller.

Example

The output of the command shows that the AP is aware of five other access points, three of which are active.

(host) #show ap radio-database

AP Radio Database

-----------------

Name Group AP Type IP Address Status Flags Switch IP 11g Mode/Chan/EIRP/Cli 11a Mode/Chan/EIRP/Cli

---- ----- ------- ---------- ------ ----- --------- ---------------------- ----------------------

mp3 default 125 10.3.129.96 Up 14h:45m:0s M 10.3.129.232 AP(HT)/10/0/0 AP(HT)/100/4/0

sw-ad-ap124-11 default 124 10.3.129.99 Up 14h:43m:18s M 10.3.129.232 AP(HT)/10/0/0 AP(HT)/100+/2/0

sw-ad-ap125-13 default 125 10.3.129.98 Up 14h:49m:36s M 10.3.129.232 AP(HT)/10/2.5/0 AP(HT)/100/4/0

sw-ad-ap65-19 default 65 10.3.129.95 Down 10.3.129.232

 

Flags: U = Unprovisioned; N = Duplicate name; G = No such group; L = Unlicensed

R = Remote AP; I = Inactive; X = Maintenance Mode; P = PPPoE AP; B = Built-in AP

S = RFprotect Sensor; d = Disconnected Sensor; H = Using 802.11n license

M = Mesh node; Y = Mesh Recovery

The output of this command includes the following information:

Column

Description

Name

Name of the AP.

Group

AP group to which the AP is associated.

AP Type

AP model type.

IP address

IP address of the AP.

Status

Current AP status. If the AP is currently up, this data column also shows the amount of time for which the AP has been active.

Flags

This column displays a letter that corresponds to some type of additional information for the AP. The key to the list of possible flags appears at the bottom of the output of this command.

Switch IP

IP address of the AP’s controller.

11g Mode/Chan/EIRP/Cli

802.1g radio type and mode/802.11g radio channel used by the AP/current Effective Isotropic Radiated Power (EIRP)/Number of Clients associated with the radio

11a Mode/Chan/EIRP/Cli

802.1a radio type and mode/802.11a radio channel used by the AP/current Effective Isotropic Radiated Power (EIRP)/Number of Clients associated with the radio.

Command History

Command

Description

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable or Config mode on Mobility Master.

/*]]>*/