You are here: Home > CLI Commands > Just_CLI_Topics > show ap radio-summary

show ap radio-summary

show ap radio‑summary

ap-group <ap-group>

ap-name <ap-name>

dot11a

dot11g

ip-addr <ip-addr>

ip6-addr <ip6-addr>

Description

Show AP radios registered to this controller.

Syntax

Parameter

Description

ap-group

Allows you to filter radio information by AP group.

ap-name <ap-name>

Allows you to filter radio information by AP name.

dot11a

Allows you to filter 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. radio information.

dot11g

Allows you to filter 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. radio information.

ip-addr <ip-addr>

Allows you to filter radio information by IP address.

ip6-addr <ip-addr>

Allows you to filter radio information by IPv6 address.

Example

The output of the command in the example below displays statistics for the AP's radio, as well as statistics for transmitted and received frames.

In the actual CLICommand-Line Interface. A console interface with a command line shell that allows users to execute text input as commands and convert these commands to appropriate functions., it will appear in a single, long table.

(host) [mynode] #show ap radio-summary

APs Radios information

----------------------

Name Group AP Type IP Address Band Mode

---- ----- ------- ---------- ---- ----

172.17.153-7 172.17.153 104 55.55.57.44 2.4 AP:1

172.17.150-5 172.17.150 104 55.55.57.42 2.4 AP:6

172.17.153-13 172.17.153 104 55.55.57.35 2.4 AP:6

172.17.151-42 172.17.151 104 55.55.57.34 2.4 AP:11

172.17.151-34 172.17.151 104 55.55.57.33 2.4 AP:11

172.17.155-26 172.17.155 104 55.55.57.22 2.4 AP:1

 

EIRP/MaxEIRP NF/U/I TD TM TC

------------ ------ -- -- --

28/29.5 -96/ 67/ 5 0/0/0/0/0/0 33/33/33/32/32/32 0/0/0/0/0/0

29.5/29.5 -96/ 27/ 3 0/0/0/0/0/0 12/11/12/12/12/11 0/0/0/0/0/0

29.5/29.5 -96/ 31/ 3 0/0/0/0/0/0 13/13/14/14/12/14 0/0/0/0/0/0

25/29.5 -96/ 28/ 6 0/0/0/0/0/0 10/10/10/9/11/10 0/0/0/0/0/0

25/29.5 -96/ 32/ 7 0/0/0/0/0/0 10/11/11/10/11/11 0/0/0/0/0/0

28/29.5 -96/ 70/ 4 0/0/0/0/0/0 27

 

NF: Noise Floor(dBm); U: Utilization(%); I: Interference(%)

TD: Time used by data frames (%); TM: time used by mgnt frames(%); time used by ctrl frames (%)

Total Radios:6

 

The output of this command includes the following information:

Parameter

Description

Name

Name of the AP.

Group

Group to which AP radio is assigned.

AP Type

AP model.

IP Address

Radio IP address.

Band

BandBand refers to a specified range of frequencies of electromagnetic radiation. on which radio is operating on (2.4 or 5 GHzGigahertz.).

Mode

Mode on which radio is operating; AP: AP Mode; AMAir Monitor. AM is a mode of operation supported on wireless APs. When an AP operates in the Air Monitor mode, it enhances the wireless networks by collecting statistics, monitoring traffic, detecting intrusions, enforcing security policies, balancing wireless traffic load, self-healing coverage gaps, and more. However, clients cannot connect to APs operating in the AM mode.: Air Monitor Mode, Spectrum: Spectrum Monitor Mode.

Optionally, you can also specify the channel number.

EIRP/Max EIRP

Current EIRPEffective Isotropic Radiated Power or Equivalent Isotropic Radiated Power. EIRP refers to the output power generated when a signal is concentrated into a smaller area by the Antenna. output and maximum EIRPEffective Isotropic Radiated Power or Equivalent Isotropic Radiated Power. EIRP refers to the output power generated when a signal is concentrated into a smaller area by the Antenna. allowed for this radio (dBmDecibel-Milliwatts. dBm is a logarithmic measurement (integer) that is typically used in place of mW to represent receive-power level. AMP normalizes all signals to dBm, so that it is easy to evaluate performance between various vendors.).

NF/U/I

Noise Floor (dBmDecibel-Milliwatts. dBm is a logarithmic measurement (integer) that is typically used in place of mW to represent receive-power level. AMP normalizes all signals to dBm, so that it is easy to evaluate performance between various vendors.) / Utilization (%) / Interference (%).

TD

Time used by data frames (%).

TM

Time used by mgmt frames(%).

TC

Time used by ctrl frames (%).

Command History

Version

Modification

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable mode on Mobility Master.

/*]]>*/