You are here: Home > CLI Commands > Just_CLI_Topics > show ap spectrum device-summary

show ap spectrum device-summary

show ap spectrum device-summary {ap-name <ap-name> | ip-addr <ip-addr> | ip6-addr <ip6-addr>} [freq-band {2.4 ghz | 5ghz}]

Description

This command shows the numbers of Wi-FiWi-Fi is a technology that allows electronic devices to connect to a WLAN network, mainly using the 2.4 GHz and 5 GHz radio bands. Wi-Fi can apply to products that use any 802.11 standard. and non-Wi-FiWi-Fi is a technology that allows electronic devices to connect to a WLAN network, mainly using the 2.4 GHz and 5 GHz radio bands. Wi-Fi can apply to products that use any 802.11 standard. device types on each channel monitored by a spectrum monitor or hybrid AP.

Syntax

Parameter

Description

ap-name <ap-name>

Name of the spectrum monitor or hybrid AP for which you want to view spectrum information.

ip-addr <ip-addr>

IP address of the spectrum monitor or hybrid AP for which you want to view spectrum information.

ip6-addr <ip6-addr>

IPv6 address of the spectrum monitor or hybrid AP for which you want to view spectrum information.

freq-band {2.4ghz | 5ghz}

View information for a specific radio type, either 2.4 GHzGigahertz. or 5 GHzGigahertz..

Usage Guidelines

Use this command to show the types of devices that the spectrum device can detect on each channel it monitors. For additional details about non-Wi-FiWi-Fi is a technology that allows electronic devices to connect to a WLAN network, mainly using the 2.4 GHz and 5 GHz radio bands. Wi-Fi can apply to products that use any 802.11 standard. device types shown in this table, see Non-Wi-Fi Interferers.

Examples

The output of this example shows that the spectrum monitor ap123 is able to detect 61 Wi-FiWi-Fi is a technology that allows electronic devices to connect to a WLAN network, mainly using the 2.4 GHz and 5 GHz radio bands. Wi-Fi can apply to products that use any 802.11 standard. devices on channel 149.

(host) [mynode] #show ap spectrum device-summary ap-name ap123 freq-band 5ghz

 

Device Summary Table

--------------------

Device 149 153 157 161 165

------- --- --- --- --- ---

Unknown 0 0 0 0 0

WIFI 61 6 14 29 9

Microwave 0 0 0 0 0

Bluetooth 0 0 0 0 0

Generic Fixed Freq 0 0 0 0 0

Cordless Phone FF 0 0 0 0 0

Video 0 0 0 0 0

Audio 0 0 0 0 0

Generic Freq Hopper 0 0 0 0 0

Cordless Phone FH 0 0 0 0 0

Xbox 0 0 0 0 0

Microwave Inverter 0 0 0 0 0

Total:12

Related Commands

Command

Description

ap spectrum local-override

Converts an AP or AMAir Monitor. AM is a mode of operation supported on wireless APs. When an AP operates in the Air Monitor mode, it enhances the wireless networks by collecting statistics, monitoring traffic, detecting intrusions, enforcing security policies, balancing wireless traffic load, self-healing coverage gaps, and more. However, clients cannot connect to APs operating in the AM mode. into a spectrum monitor by adding it to the spectrum local-override list.

rf dot11a-radio-profilemodespectrum-mode

Sets an 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. radio so that the device operates as a spectrum monitor, and can send spectrum analysis data to a desktop or laptop client.

rf dot11g-radio-profilemodespectrum-mode

Sets an 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. radio so that the device operates as a spectrum monitor, and can send spectrum analysis data to a desktop or laptop client.

Command History

Release

Modification

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms

Base operating system.

Enable or Config mode on the managed device or controller where the AP terminates.

/*]]>*/