You are here: Home > CLI Commands > Just_CLI_Topics > show ap spectrum debug monitors

show ap spectrum debug monitors

show ap spectrum debug monitors

Description

Show a detailed description of all spectrum monitors on the controller.

Syntax

No parameters.

Examples

The output of this command shows a list of available spectrum monitor or hybrid AP devices, a list of spectrum devices currently subscribed to a spectrum client, message counters for subscribed spectrum devices and the subscriptionA business model where a customer pays a certain amount as subscription price to obtain access to a product or service. history.

(host) [mynodr] #show ap spectrum debug monitors

List of Available Sensors

-----------------------------------

AP name Phy Band

------- --- ----

ap999    G 2GHz

ap999    A 5GHz

Total: 2

List of Subscriptions

---------------------

AP name Band Client IP Subscribe Time HTTPD pid Last Data Sent Send Failed

------- ---- --------- -------------- --------- -------------- -----------

ap123 2GHz 10.100.100.67 2010-05-18 03:49:44 PM 1711 1s 0

ap123 5GHz        10.100.100.67 2010-05-18 03:49:51 PM 1711       1s              0

Num Subscriptions: 2

Current Time: 2010-05-18 03:49:54 PM

Message Counters

----------------

AP name Band FFT Data FFT Duty Cycle Device Info Device Details Devices Seen Channel Info

------- ---- -------- -------------- ----------- -------------- ------------ ------------

ap123 2GHz 4 4 1 194 1 1

ap123 5GHz        0 0 0 0 0 0

Subscription History

--------------------

Message AP/Radio/Band Client IP HTTPD  Timestamp Result

pid

------- ------------- --------- ------ --------- ------

Subscribe "ap123"/1/2GHz 10.240.16.165 1701   2010-05-17 01:29:16 PM Success

Re-subscribe "ap123"/0/5GHz         10.240.16.165 1700   2010-05-17 01:29:16 PM Success

Unsubscribe-All "ap123"/-/- 10.240.16.165 1701   2010-05-17 02:44:18 PM Client Not found

Subscribe "ap123"/1/2GHz 10.100.100.67 1716   2010-05-18 03:44:28 PM Success

 

Usage Guidelines

Use this command under the guidance of an Aruba technical support representative to troubleshoot spectrum analysis errors.

Related Commands

Command

Description

ap spectrum local-override

Convert an AP or AMAir Monitor. AM is a mode of operation supported on wireless APs. When an AP operates in the Air Monitor mode, it enhances the wireless networks by collecting statistics, monitoring traffic, detecting intrusions, enforcing security policies, balancing wireless traffic load, self-healing coverage gaps, and more. However, clients cannot connect to APs operating in the AM mode. into a spectrum monitor by adding it to the spectrum local-override list.

rf dot11a-radio-profile mode spectrum-mode

Set an 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. radio so that the device operates as a spectrum monitor, and can send spectrum analysis data to a desktop or laptop client.

rf dot11g-radio-profile mode spectrum-mode

Set an 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. radio so that the device operates as a spectrum monitor, and can send spectrum analysis data to a desktop or laptop client.

Command History

Release

Modification

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms

Base operating system.

Enable or Config mode on the managed device or controller where the AP terminates.

/*]]>*/