You are here: Home > CLI Commands > Just_CLI_Topics > show ap spectrum debug

show ap spectrum debug

show ap spectrum debug {channel-info | channel-quality | classify |classify-device | classify-fft | device-details | device-info | devices-seen} {ap-name <ap-name> | ip-addr <ip-addr> | ip6-addr <ip6-addr>} freq-band {2.4ghz | 5ghz} [<count>]

Description

This command saves spectrum analysis channel information to a file on the spectrum monitor.

Syntax

Parameter

Description

channel-info

Save channel information for later analysis.

channel-quality

Save channel quality information for later analysis

classify

Save information on classification for later analysis.

classify-device

Save information on classification-related debugging with device-type for later analysis

classify-fft

Save information on classification and FFTFast Fourier Transform. FFT is a frequency analysis mechanism that aims at faster conversion of a discrete signal in time domain into a discrete frequency domain representation. See also DFT. data for later analysis.

device-details

Save device details for later analysis.

device-info

Save device information for later analysis.

devices-seen

Save information on devices seen by the spectrum monitor.

ap-name <ap-name>

Name of the spectrum monitor for which you want to view spectrum information.

ip-addr <ip-addr>

IP address of the spectrum monitor for which you want to view spectrum information.

ip6-addr <ip6-addr>

IP6 address of the spectrum monitor for which you want to view spectrum information.

freq-band {2.4ghz | 5ghz}

Save information for a specific radio type, either 2.4 GHz or 5 GHz.

<count>

Specify the number of samples to save.

Usage Guidelines

Use this command under the supervision of your Aruba technical support representative to troubleshoot spectrum analysis issues or errors. If a dump-server is defined in the AP system profile of the AP, the file created by this command will be sent from the AP to the dump-server using TFTPTrivial File Transfer Protocol. The TFTP is a software utility for transferring files from or to a remote host. .

Example

The following is an example for executing this command:

(host) [mynode] #show ap spectrum debug channel-info ap-name ap-205 freq-band 2.4ghz 22

Related Commands

Command

Description

ap spectrum local-override

Converts an AP or AMAir Monitor. AM is a mode of operation supported on wireless APs. When an AP operates in the Air Monitor mode, it enhances the wireless networks by collecting statistics, monitoring traffic, detecting intrusions, enforcing security policies, balancing wireless traffic load, self-healing coverage gaps, and more. However, clients cannot connect to APs operating in the AM mode. into a spectrum monitor by adding it to the spectrum local-override list.

rf dot11a-radio-profilemodespectrum-mode

Sets an 802.11a802.11a provides specifications for wireless systems. Networks using 802.11a operate at radio frequencies in the 5 GHz band. The specification uses a modulation scheme known as orthogonal frequency-division multiplexing (OFDM) that is especially well suited to use in office settings. The maximum data transfer rate is 54 Mbps. radio so that the device operates as a spectrum monitor, and can send spectrum analysis data to a desktop or laptop client.

rf dot11g-radio-profilemodespectrum-mode

Sets an 802.11g802.11g offers transmission over relatively short distances at up to 54 Mbps, compared with the 11 Mbps theoretical maximum of 802.11b standard. 802.11g employs Orthogonal Frequency Division Multiplexing (OFDM), the modulation scheme used in 802.11a, to obtain higher data speed. Computers or terminals set up for 802.11g can fall back to speed of 11 Mbps, so that 802.11b and 802.11g devices can be compatible within a single network. radio so that the device operates as a spectrum monitor, and can send spectrum analysis data to a desktop or laptop client.

Command History

Release

Modification

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms

Base operating system.

Enable or Config mode on the managed device or controller where the AP terminates.

/*]]>*/