You are here: Home > CLI Commands > Just_CLI_Topics > show ap system-profile

show ap system-profile

show ap system-profile [<profile-name>]

Description

This command show the system profile settings of an AP.

Syntax

Parameter

Description

<profile-name>

Name of a system profile.

Examples

The output of the command shows the current configuration settings for the default system profile.

(host) [mynode] #show ap system-profile default

 

AP system profile "default"

---------------------------

Parameter Value

--------- -----

RF Band g

RF Band for AM mode scanning all

Native VLAN ID 1

Tunnel Heartbeat Interval 10

Session ACL ap-uplink-acl

Corporate DNS Domain N/A

SNMP sysContact N/A

LED operating mode (11n/11ac APs only) normal

LED override Disabled

Driver log level emergencies

SAP MTU N/A

RAP MTU 1200 bytes

LMS IP N/A

Backup LMS IP N/A

LMS IPv6 N/A

Backup LMS IPv6 N/A

LMS Preemption Disabled

LMS Hold-down Period 600 sec

LMS ping interval 20

Remote-AP DHCP Server VLAN N/A

Remote-AP DHCP Server Id 192.168.11.1

Remote-AP DHCP Default Router 192.168.11.1

Remote-AP DHCP DNS Server N/A

Remote-AP DHCP Pool Start 192.168.11.2

Remote-AP DHCP Pool End 192.168.11.254

Remote-AP DHCP Pool Netmask 255.255.255.0

Remote-AP DHCP Lease Time 0 days

Remote-AP uplink total bandwidth 0 kbps

Remote-AP bw reservation 1 N/A

Remote-AP bw reservation 2 N/A

Remote-AP bw reservation 3 N/A

Remote-AP Local Network Access Disabled

Bootstrap threshold 8

Double Encrypt Disabled

Dump Server N/A

Heartbeat DSCP 0

Maintenance Mode Disabled

Maximum Request Retries 10

Request Retry Interval 10 sec

Number of IPSEC retries 85

AeroScout RTLS Server 2001::1:5555:disable

RTLS Server configuration N/A

RTLS Server Compatibility Mode Enabled

Telnet Disabled

Spanning Tree Disabled

AP multicast aggregation Disabled

AP ARP attack protection Disabled

AP multicast aggregation allowed VLANs none

Console enable Enabled

Shell Password N/A

Password for Backup ********

AP USB Power mode auto

RF Band for Backup all

Operation for Backup off

BLE Endpoint URL N/A

BLE Auth Token N/A

BLE Operation Mode Disabled

The output of this command includes the following information:

Column

Description

RF Band

For dual-bandBand refers to a specified range of frequencies of electromagnetic radiation. radios, this parameter displays the RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. bandBand refers to a specified range of frequencies of electromagnetic radiation. in which the AP should operate:

g = 2.4 GHzGigahertz.

a = 5 GHzGigahertz.

RF Band for AM mode scanning

Scanning bandBand refers to a specified range of frequencies of electromagnetic radiation. for multiple RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. radios.

g = 2.4 GHzGigahertz.

a = 5 GHzGigahertz.

all = Radio scans both bandsBand refers to a specified range of frequencies of electromagnetic radiation.. This is the default setting.

Native VLAN ID

Native VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. for bridge mode virtual APs (frames on the native VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. are not tagged with 802.1q tags).

Tunnel Heartbeat Interval

Interval between heartbeat messages between a remote or campus APCampus APs are used in private networks where APs connect over private links (LAN, WLAN, WAN or MPLS) and terminate directly on controllers. Campus APs are deployed as part of the indoor campus solution in enterprise office buildings, warehouses, hospitals, universities, and so on. and its associated managed device. An increase in the heartbeat interval increases the time it will take for an AP to detect the loss in connectivity to the managed device, but can reduce internet bandwidth consumed by a remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link..

Session ACL

This parameter shows the ACLAccess Control List. ACL is a common way of restricting certain types of traffic on a physical port. applied on the uplink of a remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link..

Corporate DNS Domain

DNSDomain Name System. A DNS server functions as a phone book for the intranet and Internet users. It converts human-readable computer host names into IP addresses and IP addresses into host names. It stores several records for a domain name such as an address 'A' record, name server (NS), and mail exchanger (MX) records. The Address 'A' record is the most important record that is stored in a DNS server, because it provides the required IP address for a network peripheral or element. name used by the corporate network.

SNMP sysContact

SNMPSimple Network Management Protocol. SNMP is a TCP/IP standard protocol for managing devices on IP networks. Devices that typically support SNMP include routers, switches, servers, workstations, printers, modem racks, and more. It is used mostly in network management systems to monitor network-attached devices for conditions that warrant administrative attention.  system contact information.

LED operating mode

Displays the LEDLight Emitting Diode. LED is a semiconductor light source that emits light when an electric current passes through it. operating mode for indoor 802.11n802.11n is a wireless networking standard to improve network throughput over the two previous standards, 802.11a and 802.11g. With 802.11n, there will be a significant increase in the maximum raw data rate from 54 Mbps to 600 Mbps with the use of four spatial streams at a channel width of 40 MHz. APs. LEDs display as usual in the default normal operating mode, but are all turned off in off mode.

SAP MTU

Maximum Transmission Unit (MTUMaximum Transmission Unit. MTU is the largest size packet or frame specified in octets (eight-bit bytes) that can be sent in networks such as the Internet.) size, in bytes. This value describes the greatest amount of data that can be transferred in one physical frame.

LMS IP

The IP address of the local management switch (LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. )—the Aruba managed device which is responsible for terminating user traffic from the APs, and processing and forwarding the traffic to the wired network.

NOTE: If the LMS-IP is blank, the access point will remain on the managed device that it finds using methods like DNS or DHCP. If an IP address is configured for the LMS IP parameter, the AP will be immediately redirected to the managed device at that address.

Backup LMS IP

For networks with multiple managed devices, this parameter displays the IP address of a backup to the IP address specified with the lms-ip parameter.

LMS IPv6

For IPv6 networks with multiple managed devices, this parameter specifies the IPv6 address of the local management switch (LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. )—the Aruba managed device—which is responsible for terminating user traffic from the APs, and processing and forwarding the traffic to the wired network. This can be the IP address of the managed device or Mobility Master.

Backup LMS IPv6

In multi-controller ipv6 networks, this parameter specifies the IPv6 address of a backup to the IPv6 address specified with the LMS IPv6 setting.

LMS Preemption

When this parameter is enabled, the local management switch automatically reverts to the primary LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. IP address when it becomes available.

LMS Hold-down Period

Time, in seconds, that the primary LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. must be available before an AP returns to that LMSLocal Management Switch. In multi-controller networks, each controller acts as an LMS and terminates user traffic from the APs, processes, and forwards the traffic to the wired network. after failover. The rap-dhcp-server-vlanVLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. ID of the remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link. DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server is used if the managed device is unavailable. This VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. enables the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server on the AP (also known as the remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link. DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN.). If you enter the native VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. ID, the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server is unavailable.

Remote-AP DHCP Server VLAN

VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. ID of the remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link. DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server used if the managed device is unavailable. This VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. enables the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server on the AP (also known as the remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link. DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN.).

Remote-AP DHCP Server ID

IP address used as the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  server identifier.

Remote-AP DNS Server

IP address of the DNSDomain Name System. A DNS server functions as a phone book for the intranet and Internet users. It converts human-readable computer host names into IP addresses and IP addresses into host names. It stores several records for a domain name such as an address 'A' record, name server (NS), and mail exchanger (MX) records. The Address 'A' record is the most important record that is stored in a DNS server, because it provides the required IP address for a network peripheral or element. server.

Remote-AP DHCP Default Router

IP address for the default DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  router.

Remote-AP DHCP Pool Start

This parameter defines the starting IP address in the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  pool for remote APsRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link..

Remote-AP DHCP PoolEnd

This parameter defines the last IP address in the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  pool for remote APsRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link..

Remote-AP DHCP PoolNetmask

Configures a DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  pool for remote APsRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link.. This is the netmaskNetmask is a 32-bit mask used for segregating IP address into subnets. Netmask defines the class and range of IP addresses. used for the DHCPDynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network.  pool.

Remote-AP uplink total bandwidth

This is the total reserved uplink bandwidth (in kilobits per second).

Remote-AP bw reservation 1 Remote-AP bw reservation 2 Remote-AP bw reservation 3

Session ACLsAccess Control List. ACL is a common way of restricting certain types of traffic on a physical port. with uplink bandwidth reservation in kilobits per second. You can specify up to three session ACLsAccess Control List. ACL is a common way of restricting certain types of traffic on a physical port. to reserve uplink bandwidth. The sum of the three uplink bandwidths should not exceed the rap-bw-total value.

Remote-AP Local Network Access

Shows if Remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link. Local Network Access is enabled or disabled. By enabling this option, the clients that are connected to a remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link. can communicate.

NOTE: By default, the Remote APRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link. Local Network Access will be disabled.

Bootstrap threshold

Number of consecutive missed heartbeats on a GREGeneric Routing Encapsulation. GRE is an IP encapsulation protocol that is used to transport packets over a network. tunnel (heartbeats are sent once per second on each tunnel) before an AP rebootstraps. On the managed device, the GREGeneric Routing Encapsulation. GRE is an IP encapsulation protocol that is used to transport packets over a network. tunnel timeout is 1.5 x bootstrap-threshold; the tunnel is torn down after this number of seconds of inactivity on the tunnel.

Double Encrypt

This parameter applies only to remote APsRemote APs extend corporate network to the users working from home or at temporary work sites. Remote APs are deplyed at branch office sites and are connected to the central network on a WAN link.. Double encryption is used for traffic to and from a wireless client that is connected to a tunneled SSIDService Set Identifier. SSID is a name given to a WLAN and is used by the client to access a WLAN network.. When enabled, all traffic is re-encrypted in the IPsecInternet Protocol security. IPsec is a protocol suite for secure IP communications that authenticates and encrypts each IP packet in a communication session. tunnel. When disabled, the wireless frame is only encapsulated inside the IPsecInternet Protocol security. IPsec is a protocol suite for secure IP communications that authenticates and encrypts each IP packet in a communication session. tunnel.

Dump Server

(For debugging purposes.) Displays the server to receive the core dump generated if an AP process crashes.

Heartbeat DSCP

DSCPDifferentiated Services Code Point. DSCP is a 6-bit packet header value used for traffic classification and priority assignment. value of AP heartbeats (0–63).

Maintenance Mode

Shows if Maintenance mode is enabled or disabled. If enabled, APs stop flooding unnecessary traps and syslog messages to the NMSNetwork Management System. NMS is a set of hardware and/or software tools that allow an IT professional to supervise the individual components of a network within a larger network management framework. or network operations centers when deploying, maintaining, or upgrading the network. The managed device still generates debug syslog messages if debug logging is enabled.

Maximum Request Retries

Maximum number of times to retry AP-generated requests, including keepaliveSignal sent at periodic intervals from one device to another to verify that the link between the two devices is working. If no reply is received, data will be sent by a different path until the link is restored. A keepalive can also be used to indicate that the connection should be preserved so that the receiving device does not consider it timed out and drop it. messages. After the maximum number of retries, the AP either tries the IP address specified by the bkup-lms-ip (if configured) or reboots.

Request Retry Interval

Interval, in seconds, between the first and second retries of AP-generated requests. If the configured interval is less than 30 seconds, the interval for subsequent retries is increased up to 30 seconds.

Number of IPSEC retries

The number of times the AP will attempt to recreate an IPsecInternet Protocol security. IPsec is a protocol suite for secure IP communications that authenticates and encrypts each IP packet in a communication session. tunnel with Mobility Master before the AP will reboot. A value of 0 disables the reboot.

AeroScout RTLS Server

This parameter contains the following information, separated by colons:

IPv4 or IPv6 address of an AeroScout real-time asset location (RTLSReal-Time Location Systems. RTLS automatically identifies and tracks the location of objects or people in real time, usually within a building or other contained area.) server to which locations report are sent

Port number: Port number on the AeroScout server to which location reports are sent

include-unassoc-sta - Specifies whether to include unassociated stations when sending station reports. Unassociated stations are stations that are not associated to any AP

Default: disabled

RTLS Server configuration

This parameter contains the following information, separated by colons.

IPv4 or IPv6 address of the RTLSReal-Time Location Systems. RTLS automatically identifies and tracks the location of objects or people in real time, usually within a building or other contained area. server to which the AP sends RFIDRadio Frequency Identification. RFID uses radio waves to automatically identify and track the information stored on a tag attached to an object. tag information.

Number of the RTLSReal-Time Location Systems. RTLS automatically identifies and tracks the location of objects or people in real time, usually within a building or other contained area. server port to which the AP sends RFIDRadio Frequency Identification. RFID uses radio waves to automatically identify and track the information stored on a tag attached to an object. tag information

Shared secret key for the server

Frequency at which packets are sent to the server, in seconds

AP USB Power mode

Displays the status of USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices. port on various AP platforms that have external USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices. ports. Listed below are the power modes:

auto- Detect USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices.  power mode automatically

disable- Disable USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices.  power

enable- Enable USBUniversal Serial Bus. USB is a connection standard that offers a common interface for communication between the external devices and a computer. USB is the most common port used in the client devices.  power

NOTE: This parameter can be configured only on AP-214, AP-215, AP-224, AP-225, AP-205H, AP-303H, AP-304, AP-305, AP-314, AP-315, AP-324, AP-325, AP-334, AP-335, AP-344, AP-345, AP-203R, and AP-203RP access points only.

Telnet

Reports whether telnet access the AP is enabled or disabled.

RF Band for Backup

If the system profile is enabled AP console access using a backup ESSIDExtended Service Set Identifier. ESSID refers to the ID used for identifying an extended service set., this parameter

Operation for Backup

This parameter allows AP console access using a backup ESSIDExtended Service Set Identifier. ESSID refers to the ID used for identifying an extended service set., allowing users to access an AP console after the AP has disconnected from the managed device. When the AP advertises a backup ESSIDExtended Service Set Identifier. ESSID refers to the ID used for identifying an extended service set. in either static or dynamic mode, a user is able to access and debug the AP remotely through a virtual AP. This feature is disabled by default.

BLE Endpoint URL

Displays the URLUniform Resource Locator. URL is a global address used for locating web resources on the Internet. of the Meridian server to which the Bluetooth Low Energy (BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption.) sends monitoring data.

BLE Auth Token

Displays the BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. endpoint authorization token. This token is unique for each deployment.

BLE Operation Mode

Displays the BLEBluetooth Low Energy. The BLE functionality is offered by Bluetooth® to enable devices to run for long durations with low power consumption. operation mode of the AP.

Starting from ArubaOS 8.2.0.0, the output of the show ap system-profile <profile-name> | include IPM command is modified to display a new output parameter, IPM Steps delete all.

(host) [mynode] #show ap system-profile default | include IPM

IPM activation Disabled

IPM power reduction steps with priorities N/A

IPM Steps delete all No

Starting from ArubaOS 8.4.0.0, the output of the show ap system-profile <profile-name> | include USB command is modified to display a new output parameter, AP USB Power mode.

(host) [mynode] #show ap system-profile default | include USB

AP USB Power mode auto

Related Commands

Command

Description

ap system-profile

This command configures an AP system profile.

Command History

Release

Modification

ArubaOS 8.4.0.0

The following changes were introduced:

The output of the show ap system-profile <profile-name> | include USB command displays the AP USB Power mode parameter.

The AeroScout RTLS Server and RTLS Server configuration output parameter of the show ap system-profile <profile-name> | include RTLS command displays IPv6 address.

ArubaOS 8.2.0.0

A new output parameter, IPM Steps delete all, was included in the output of the show ap system-profile <profile-name> | include IPM command.

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms

Base operating system.

Enable or Config mode on the managed device or controller where the AP terminates.

/*]]>*/