You are here: Home > CLI Commands > Just_CLI_Topics > show ap arm client-match summary

show ap arm client-match summary

show ap arm client-match summary [client-mac <macaddr>]|[advanced]|[brief]

Description

If the client match feature is enabled, the output of this command shows the history of AP association changes triggered by the client match feature.

Syntax

Parameter

Description

client-mac <macaddr>

MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address of a client for which you want to view a history of AP association changes triggered by the client match feature.

advanced

Displays advanced debugging information. Include this parameter only under the supervision of Aruba support.

brief

Displays brief statistical information containing the final calculated data of the output parameters.

Example

The following command displays information on the Client Match summary.

((host) [mynode](config) #show ap arm client-match summary

 

SM: Sticky Moves, BM: Bandsteer Moves, LM: Load Balance Moves, MU: MUsteer Moves, VoM: Voice Roam M oves, HM: HE Moves

T: Total, S: Success

ACC: Accept, REJ#: Reject with reason #, TO: Timeout FA: False Accept

11v Move Format: (T/ACC/REJ1/REJ2/REJ3/REJ4/REJ5/REJ6/REJ7/REJ8/TO/FA)

Client Match Summary

---------------------

MAC SM (T/S) LM (T/S) BM (T/S) MU (T/S) VoM (T/S) HM (T/S) Moves (T/S) Last Move (Time/Rsn/ Dur)) Device Type 11v Moves

--- -------- -------- -------- -------- --------- -------- ----------- -------------------- ----- ----------- ---------

Total clients:0

Sticky (T/S):0/0 Deauth (T/S):0/0 11v-BTM: 0/0/0/0/0/0/0/0/0/0/0/0

Load-balance (T/S):0/0 Deauth (T/S):0/0 11v-BTM: 0/0/0/0/0/0/0/0/0/0/0/0

Band-steer (T/S):0/0 Deauth (T/S):0/0 11v-BTM: 0/0/0/0/0/0/0/0/0/0/0/0

Voice-roam (T/S):0/0 Deauth (T/S):0/0 11v-BTM: 0/0/0/0/0/0/0/0/0/0/0/0

MU-Steer (T/S):0/0 Deauth (T/S):0/0 11v-BTM: 0/0/0/0/0/0/0/0/0/0/0/0

HE-steer (T/S):0/0 Deauth (T/S):0/0 11v-BTM: 0/0/0/0/0/0/0/0/0/0/0/0

The output of this command includes the following parameters:

Parameter Description
MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network.

MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address of the client that was moved to a different AP radio.

SM (T/S)
Sticky Moves

The output of this column shows the following two values:

T: Total number of times the client match feature attempted to move a mobile roaming client because it was staying associated (sticking) to a sub-optimal AP.

S: Number of times the client match successfully moved a mobile roaming client because it was staying associated (sticking) to a sub-optimal AP.

LM (T/S)
Load Balance Moves

The output of this column shows the following two values:

T: Total number of times the client match feature attempted to move an AP to a different radio on dual-radio AP to balance the client load between the AP radios.

S: Number of times the client match feature successfully moved an AP to a different radio on dual-radio AP to balance the client load between the AP radios.

BM (T/S)
Bandsteer Moves

The output of this column shows the following two values:

T: Total number of times the client match feature attempted to steer a dual-bandBand refers to a specified range of frequencies of electromagnetic radiation. client to a 5GHz radio.

S: Number of times the client match feature successfully moved a dual-bandBand refers to a specified range of frequencies of electromagnetic radiation. client to a 5GHz radio.

MU (T/S)
MU steer Moves

The output of this column shows the following two values:

T: Total number of times the Client Match feature attempted to steer and align MU-MIMOMulti-User Multiple-Input Multiple-Output. MU-MIMO is a set of multiple-input and multiple-output technologies for wireless communication, in which users or wireless terminals with one or more antennas communicate with each other. -capable clients with MU-MIMOMulti-User Multiple-Input Multiple-Output. MU-MIMO is a set of multiple-input and multiple-output technologies for wireless communication, in which users or wireless terminals with one or more antennas communicate with each other. -capable radios.

S: Number of times the client match feature successfully moved an AP to a different radio.

VoM (T/S)
Voice Roam Moves

The output of this column shows the following two values:

T: Total number of times the client match feature attempted to move a voice client roaming from one AP BSSBasic Service Set. A BSS is a set of interconnected stations that can communicate with each other. BSS can be an independent BSS or infrastructure BSS. An independent BSS is an ad hoc network that does not include APs, whereas the infrastructure BSS consists of an AP and all its associated clients. to another AP BSSBasic Service Set. A BSS is a set of interconnected stations that can communicate with each other. BSS can be an independent BSS or infrastructure BSS. An independent BSS is an ad hoc network that does not include APs, whereas the infrastructure BSS consists of an AP and all its associated clients. using the same SSIDService Set Identifier. SSID is a name given to a WLAN and is used by the client to access a WLAN network..

S: Number of times the client match feature successfully moved a roaming voice client roaming from one AP BSSBasic Service Set. A BSS is a set of interconnected stations that can communicate with each other. BSS can be an independent BSS or infrastructure BSS. An independent BSS is an ad hoc network that does not include APs, whereas the infrastructure BSS consists of an AP and all its associated clients. to another using AP BSSBasic Service Set. A BSS is a set of interconnected stations that can communicate with each other. BSS can be an independent BSS or infrastructure BSS. An independent BSS is an ad hoc network that does not include APs, whereas the infrastructure BSS consists of an AP and all its associated clients.  the same SSIDService Set Identifier. SSID is a name given to a WLAN and is used by the client to access a WLAN network..

Moves(T/S)

The output of this column shows the following two values:

T: Total number of times the client match feature attempted to move an AP to a different radio.

S: Number of times the client match feature successfully moved an AP to a different radio.

Last Move

This column shows the date and time the client was steered to a different AP radio, the reason why the client match feature made the change, and the number of seconds it took for the change to take place. Possible reasons include:

Sticky: A mobile roaming client was staying associated (sticking) to a sub-optimal AP for too long.

Band steer: A dual-bandBand refers to a specified range of frequencies of electromagnetic radiation. capable client was steered toward a 5Ghz radio on a dual-bandBand refers to a specified range of frequencies of electromagnetic radiation. AP.

Band Balance: A dual-bandBand refers to a specified range of frequencies of electromagnetic radiation. capable client was steered toward a different radio to balance the load between the two radios on a single AP.

Load Balance: Client match moved the client to a different AP, based upon the load on APs in the client's RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. neighborhood, and the SNRSignal-to-Noise Ratio. SNR is used for comparing the level of a desired signal with the level of background noise. levels the client detected from each underutilized AP.

HE-Steer: A HE capable client was steered to a HE capable AP on the same bandBand refers to a specified range of frequencies of electromagnetic radiation..

Device type

Type of client, if the value can be determined.

11v Moves (T/ACCAdvanced Cellular Coexistence. The ACC feature in APs enable WLANs to perform at peak efficiency by minimizing interference from 3G/4G/LTE networks, distributed antenna systems, and commercial small cell/femtocell equipment./REJ1/REJ2/REJ3/REJ4
/REJ5/REJ6/REJ7/REJ8/TO/FA)

The output of this column shows the following values:

T: Total number of times the client match feature attempted to move an AP to a different radio using the 802.11v802.11v is an IEEE standard that allows client devices to exchange information about the network topology and RF environment. This information is used for assigning best available radio resources for the client devices to provide seamless connectivity. BSSBasic Service Set. A BSS is a set of interconnected stations that can communicate with each other. BSS can be an independent BSS or infrastructure BSS. An independent BSS is an ad hoc network that does not include APs, whereas the infrastructure BSS consists of an AP and all its associated clients. transition management request.

ACCAdvanced Cellular Coexistence. The ACC feature in APs enable WLANs to perform at peak efficiency by minimizing interference from 3G/4G/LTE networks, distributed antenna systems, and commercial small cell/femtocell equipment.: Number of times a client returned a 802.11v802.11v is an IEEE standard that allows client devices to exchange information about the network topology and RF environment. This information is used for assigning best available radio resources for the client devices to provide seamless connectivity. accept message.

REJ1: Move Rejected; unspecified reject reason

REJ2: Move Rejected; Insufficient Beacons

REJ3: Move Rejected; Insufficient capacity

REJ4: Move Rejected; BSSBasic Service Set. A BSS is a set of interconnected stations that can communicate with each other. BSS can be an independent BSS or infrastructure BSS. An independent BSS is an ad hoc network that does not include APs, whereas the infrastructure BSS consists of an AP and all its associated clients. Termination undesired

REJ5: Move Rejected; BSSBasic Service Set. A BSS is a set of interconnected stations that can communicate with each other. BSS can be an independent BSS or infrastructure BSS. An independent BSS is an ad hoc network that does not include APs, whereas the infrastructure BSS consists of an AP and all its associated clients. Termination Delay requested

REJ6:Move Rejected; STA BSSBasic Service Set. A BSS is a set of interconnected stations that can communicate with each other. BSS can be an independent BSS or infrastructure BSS. An independent BSS is an ad hoc network that does not include APs, whereas the infrastructure BSS consists of an AP and all its associated clients. Trans List provided

REJ7: Move Rejected; No Suitable candidate

REJ8: Move Rejected; Leaving ESSExtended Service Set. An ESS is a set of one or more interconnected BSSs that form a single sub network.

TO: Number of times the dot11v BSSBasic Service Set. A BSS is a set of interconnected stations that can communicate with each other. BSS can be an independent BSS or infrastructure BSS. An independent BSS is an ad hoc network that does not include APs, whereas the infrastructure BSS consists of an AP and all its associated clients. transition management request timed out because the client failed to acknowledge the 802.11v802.11v is an IEEE standard that allows client devices to exchange information about the network topology and RF environment. This information is used for assigning best available radio resources for the client devices to provide seamless connectivity. BSSBasic Service Set. A BSS is a set of interconnected stations that can communicate with each other. BSS can be an independent BSS or infrastructure BSS. An independent BSS is an ad hoc network that does not include APs, whereas the infrastructure BSS consists of an AP and all its associated clients. transition management request from the AP.

FA: Number of false accepts, where the client responds to a move request with an accept message, but fails to move to the destination radio and remains on the same radio.

Related Commands

Command

Description

rf arm-profile

This command enables ClientMatch.

show ap arm client-match probe-report

This command displays the client probe report for the specified AP.

show ap arm client-match neighbors

This command displays the BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly. of other APs seen by clients in the select AP's RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. neighborhood.

show ap arm virtual-beacon-report

This command displays the virtual beacon report for an AP with a specific IP or MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address.

show ap arm client-match unsupported

This command displays a list of clients that failed to be steered to a more optimal AP, and the reason the initial steering request was triggered.

show ap arm client-match history

This command shows the history of AP association changes triggered by the client match feature.

show ap arm client-match restriction-table

This command displays the list of clients that ClientMatch has restricted from the specified AP.

Command History

Command

Description

ArubaOS 8.3.0.0

A new parameter, brief was added.

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

base operating system.

Enable or Config mode on Mobility Master.

/*]]>*/