You are here: Home > CLI Commands > Just_CLI_Topics > show rf optimization-profile

show rf optimization-profile

show rf optimization-profile [<profile>]

Description

Show an Optimization profile.

Syntax

Parameter

Description

<profile>

name of an ARMAdaptive Radio Management. ARM dynamically monitors and adjusts the network to ensure that all users are allowed ready access. It enables full utilization of the available spectrum to support maximum number of users by intelligently choosing the best RF channel and transmit power for APs in their current RF environment. profile

Usage Guidelines

Issue this command without the <profile>parameter to display the entire Optimization profile list, including profile status and the number of references to each profile. Include a profile name to display detailed configuration information for that profile.

Examples

The example below shows that the controller has two configured Optimization profiles. The References column lists the number of other profiles with references to the Optimization profile, and the Profile Status column indicates whether the profile is predefined. User-defined profiles will not have an entry in the Profile Status column.

(host)[mynode]# show rf optimization-profile

RF Optimization Profile List

----------------------------

Name References Profile Status

---- ---------- --------------

default 6

profile2 1

 

Total:2

This example displays the configuration settings for the profile profile2.

(host)[mynode]#show rf optimization-profile profile2

RF Optimization Profile "profile2"

---------------------------------

Parameter Value

--------- -----

Station Handoff Assist Disabled

Detect Association Failure Disabled

Coverage Hole Detection Disabled

Hole Good RSSI Threshold 20

Hole Good Station Ageout 30 sec

Hole Detection Interval 180 sec

Hole Idle Station Ageout 90 sec

Hole Poor RSSI Threshold 10

Detect interference Disabled

Interference Threshold 90 %

Interference Threshold Exceed Time 25 sec

Interference Baseline Time 25 sec

RSSI Falloff Wait Time 4

Low RSSI Threshold 10

RSSI Check Frequency 3 sec

The output of this command includes the following parameters:

Parameter

Description

Station Handoff Assist

If enabled, this parameter allows the controller to force a client off an AP when the RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values. drops below a defined minimum threshold.

Detect Association Failure

Shows if the profile enables or disables STA association failure detection.

Coverage Hole Detection

Shows if the profile enables or disables coverage hole detection.

Hole Good RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values. Threshold

Time, in seconds, after a coverage hole is detected until a coverage hole event notification is generated.

This parameter requires the RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. Protect license.

Hole Good Station Ageout

Stations with signal strength above this value are considered to have good coverage.

This parameter requires the RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. Protect license.

Hole Detection Interval

Time, in seconds, after which a station with good coverage is aged out.

This parameter requires the RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. Protect license.

Hole Idle Station Ageout

Time, in seconds, after which a station in a poor coverage area is aged out.

This parameter requires the RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. Protect license.

Hole Poor RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values. Threshold

Stations with signal strength below this value will trigger detection of a coverage hole.

This parameter requires the RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. Protect license.

Detect interference

Enables or disables interference detection.

Interference Threshold

Percentage increase in the frame retry rate or frame receive error rate before interference monitoring begins on a given channel.

Interference Threshold Exceed Time

Time, in seconds, the FRR or FRER exceeds the threshold before interference is reported.

Interference Baseline Time

Time, in seconds, the air monitor should learn the state of the link between the AP and client to create frame retry rate and frame receive error rate baselines.

RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values. Falloff Wait Time

Number of times the detected client RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values. level must fall below the minimum RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values. threshold the before the AP sends a deauthorization message to the client. The maximum value is 8 times.

Low RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values. Threshold

Minimum RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values. above which deauthorization messages should never be sent.

RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values. Check Frequency

Interval, in seconds, to sample RSSIReceived Signal Strength Indicator. RSSI is a mechanism by which RF energy is measured by the circuitry on a wireless NIC (0-255). The RSSI is not standard across vendors. Each vendor determines its own RSSI scale/values..

Related Commands

Related Command

Description

rf optimization-profile

This command configures the RFRadio Frequency. RF refers to the electromagnetic wave frequencies within a range of 3 kHz to 300 GHz, including the frequencies used for communications or Radar signals. optimization profile.

Command History

Release

Modification

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platform

License

Command Mode

All platforms

Base operating system.

Config mode on Mobility Master.

/*]]>*/