You are here: Home > CLI Commands > Just_CLI_Topics > show wms probe

show wms probe

show wms probe

Description

This command displays detailed information on WMS probes.

Syntax

No parameters.

Example

This example shows the Probe List table for WMS probes. The output below has been split into two tables to better fit in this document. In the actual CLICommand-Line Interface. A console interface with a command line shell that allows users to execute text input as commands and convert these commands to appropriate functions., this information appears in a single, long table.

(host) [mynode] #show wms probe

 

Probe List

----------

Monitor Eth MAC BSSID PHY Type IP LMS IP Scan Status Updates Reqs/Fails Stats Type

--------------- ----- -------- -- ------ ---- ------ ------- ---------- ----- ----

40:e3:d6:cf:61:96 40:e3:d6:76:19:60 80211GHT-20mhz 191.191.191.252 192.192.189.1 No Up 6850 1/0 0 soft-ap

40:e3:d6:cf:61:96 40:e3:d6:76:19:70 80211AVHT-80mhz 191.191.191.252 192.192.189.1 No Up 6860 0/0 0 soft-ap

40:e3:d6:c0:dc:ae 40:e3:d6:8d:ca:e0 80211GHT-20mhz 191.191.191.253 192.192.189.1 No Up 6924 1/0 0 soft-ap

40:e3:d6:c0:dc:ae 40:e3:d6:8d:ca:f0 80211AVHT-80mhz 191.191.191.253 192.192.189.1 No Up 6909 0/0 0 soft-ap

Total:4

Column

Description

Monitor Eth MAC

EthernetEthernet is a network protocol for data transmission over LAN. MACMedia Access Control. A MAC address is a unique identifier assigned to network interfaces for communications on a network. address of a probe.

BSSID

Probe Radio BSSIDBasic Service Set Identifier. The BSSID identifies a particular BSS within an area. In infrastructure BSS networks, the BSSID is the MAC address of the AP. In independent BSS or ad hoc networks, the BSSID is generated randomly..

PHY Type

Radio PHY type:

802.11A

802.11AHT-40Mbps

802.11AHT-20Mbps

802.11G

802,11GHT-20Mbps

IP

IP address of the AP.

LMS IP

IP address of the AP’s managed device.

Scan

Shows if the Air Monitor is performing scanning.

Status

If the scan column displays a status of Up, the AP or AMAir Monitor. AM is a mode of operation supported on wireless APs. When an AP operates in the Air Monitor mode, it enhances the wireless networks by collecting statistics, monitoring traffic, detecting intrusions, enforcing security policies, balancing wireless traffic load, self-healing coverage gaps, and more. However, clients cannot connect to APs operating in the AM mode. is active

Updates

Number of updates the AP or AMAir Monitor. AM is a mode of operation supported on wireless APs. When an AP operates in the Air Monitor mode, it enhances the wireless networks by collecting statistics, monitoring traffic, detecting intrusions, enforcing security policies, balancing wireless traffic load, self-healing coverage gaps, and more. However, clients cannot connect to APs operating in the AM mode. sent to the WMS database since the managed device was last reset.

Reqs/Fails

Number of database update requests that have not yet been added into the database. and the number of failed database requests.

Stats

Total number of statistics updates sent to the database.

Type

A WMS AP type can be one of the following:

soft-ap: An Aruba Access Point (AP).

air-monitor: An Aruba Air Monitor (AMAir Monitor. AM is a mode of operation supported on wireless APs. When an AP operates in the Air Monitor mode, it enhances the wireless networks by collecting statistics, monitoring traffic, detecting intrusions, enforcing security policies, balancing wireless traffic load, self-healing coverage gaps, and more. However, clients cannot connect to APs operating in the AM mode.).

Related Commands

Command

Description

wms ap

This command allows you to classify an AP into one of several categories.

wms client

This command allows you to classify a wireless client into one of several categories.

Command History

Release

Release

ArubaOS 8.0.0.0

Command Introduced.

Command Information

Platforms

Licensing

Command Mode

All platforms

Base operating system.

Enable or Config mode on Mobility Master.

/*]]>*/