You are here: Home > CLI Commands > Just_CLI_Topics > traceoptions

traceoptions

traceoptions

chassis-manager flags {all|association|debug|environment-monitoring|fru|interface|interface-statistics|ipc|poe-configuration|poe-statistics|statistics-sync|system-statistics}

igmp flags {all|debug|leave|query|report}

igmp-snooping flags {all|config|errors|receive|transmit}

interface-manager {flags {all|configuration|dhcp-client|ethernet|infrastructure|lacp|loopback|mgmt|oam|port-channel|port-mirroring|system-information|tunnel|vlan} | level {debug|error|verbose}}

layer2-forwarding {flags{all|config|fdb|hsl|interface|ipc|learning|nexthop|port-loop-protect|sysinfo|task|timer|tunneled-node|vlan|vlan-assignment|vlan-port} | level{debugging|errors|informational} |  {size <tracefile_size>}}

lldp flags {all|errors|receive|system-state|transmit}

mstp {flags {all|config|debug|port-information|received-bpdu-all|role-selection|sent-bpdu-all|state-machine-changes|system|topology-change|} | port<mstp_trace_port>}

no

ospf flags {all|cnf|db|dd|debug|dr-elec|flood|hello|lsa|lsr|lsu|msm|pkt-all|spf|state}

pim flags {adjacency|all|debug|jp-asserts|register|route|state}

rmon {flags {alarm|all|cli|event|history|ifstat|log|snmp} | {level {alert|critical|debugging|emergency|errors|informational|notice|warning} | size <trace_file_ize>}

routing flags {all|arp|configuration|event|interface|route}

stack-manager {flags {adjacency|all|asp|configuration|primary-election|route|system} | level {alert|critical|debugging|emergency|errors|informational|notice|warning}

 

Description

This command configures the traceoptions to monitor and log traffic flows.

Syntax

Parameter

Description

chassis-manager flags

Configures the chassis manager trace options:

all—Enables all chassis manager debug tracing.

association—Enables stack membership and association tracing.

debug—Enables generic chassis manager debug tracing.

environment-monitoring—Enables environment monitor debug tracing.

fru— Enables FRU reporting and management tracing.

interface—Enables interface debug tracing.

interface-statistics—Enables packet statistics on interface tracing.

ipc—Enables inter-process message exchange tracing.

poe-configuration—Enables power-over-ethernet configuration tracing.

poe-statistics—Enables power-over-ethernet statistics tracing.

statistics-sync—Enables statistics tracing.

system-statistics—Enables chassis system statistics tracing.

igmp flags

Configures the IGMPInternet Group Management Protocol. Communications protocol used by hosts and adjacent routers on IP networks to establish multicast group memberships. trace options:

all—Enables tracing on all IGMPInternet Group Management Protocol. Communications protocol used by hosts and adjacent routers on IP networks to establish multicast group memberships. modules.

debug—Enables internal state tracing for IGMPInternet Group Management Protocol. Communications protocol used by hosts and adjacent routers on IP networks to establish multicast group memberships. modules.

leave—Enables IGMPInternet Group Management Protocol. Communications protocol used by hosts and adjacent routers on IP networks to establish multicast group memberships. leave processing tracing.

query—Enables IGMPInternet Group Management Protocol. Communications protocol used by hosts and adjacent routers on IP networks to establish multicast group memberships. query processing tracing.

report—Enables IGMPInternet Group Management Protocol. Communications protocol used by hosts and adjacent routers on IP networks to establish multicast group memberships. report processing tracing.

igmp-snooping flags

Configures the IGMPInternet Group Management Protocol. Communications protocol used by hosts and adjacent routers on IP networks to establish multicast group memberships. snooping trace options:

all—Enables tracing on all igmp-snooping modules.

config—Enables igmp-snooping configuration tracing.

errors— Enables igmp-snooping error tracing.

receive—Enables igmp-snooping PDUPower Distribution Unit or Protocol Data Unit. Power Distribution Unit is a device that distributes electric power to the networking equipment located within a data center. Protocol Data Unit contains protocol control Information that is delivered as a unit among peer entities of a network. received (RX) tracing.

transmit—Enables igmp-snooping PDUPower Distribution Unit or Protocol Data Unit. Power Distribution Unit is a device that distributes electric power to the networking equipment located within a data center. Protocol Data Unit contains protocol control Information that is delivered as a unit among peer entities of a network. transmit (TX) tracing.

interface-manager {flags|level}

Configures the interface manager trace flags:

all—Enables all interface manager debug message tracing.

configuration—Enables configuration debug tracing.

dhcp-client—Enables dhcp client debug tracing.

ethernet—Enables ethernet interface debug tracing.

infrastructure—Enables infrastructure debug tracing.

lacp—Enables LACPLink Aggregation Control Protocol. LACP is used for the collective handling of multiple physical ports that can be seen as a single channel for network traffic purposes. debug tracing.

loopback—Enables loopback interface debug tracing.

mgmt—Enables management interface debug tracing.

oam—Enables OAM debug tracing.

port-channel—Enables port-channel debug tracing.

port-mirroring—Enables port mirroring debug tracing.

system-information—Enables system debug messages tracing.

tunnel—Enables tunnel interface debug tracing.

vlan—Enables vlanVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. interface debug tracing.

Configures the level for interface manager tracing:

debug—Debug messages

error—Error messages

verbose—Verbose debug messages

layer2-forwarding {flags|level|size}

Configures the layer2 forwarding trace flags:

all—Enables tracing on all switching modules.

config—Enables config module tracing.

fdb—Enables forwarding database module tracing.

hsl—Enables HSL module tracing.

interface—Enables interface module tracing.

ipc—Enables IPC tracing.

learning—Enables learning module tracing.

nexthop—Enables nexthop module tracing.

port-loop—Enables Port loop protect Protocol tracing.

sysinfo—Enables sysinfo module tracing.

task—Enables task tracing.

timer—Enables task timer tracing.

tunneled-node—Enables tunneled-node module tracing.

vlan—Enables vlanVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. module tracing.

vlan-assignment—Enables VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. assignment module tracing.

vlan-port—Enables VLANVirtual Local Area Network. In computer networking, a single Layer 2 network may be partitioned to create multiple distinct broadcast domains, which are mutually isolated so that packets can only pass between them through one or more routers; such a domain is referred to as a Virtual Local Area Network, Virtual LAN, or VLAN. port module tracing.

Configures the layer2 forwarding tracing levels:

debug—Debug messages

error—Error messages

informational—Informational messages

Configures the maximum size for layer2 forwarding trace file in MB.

lldp flags

Configures the LLDPLink Layer Discovery Protocol. LLDP is a vendor-neutral link layer protocol in the Internet Protocol suite used by network devices for advertising their identity, capabilities, and neighbors on an IEEE 802 local area network, which is principally a wired Ethernet. trace options:

all—Enables tracing on all lldp modules.

errors—Enables lldp error tracing.

receive—Enables lldp PDUPower Distribution Unit or Protocol Data Unit. Power Distribution Unit is a device that distributes electric power to the networking equipment located within a data center. Protocol Data Unit contains protocol control Information that is delivered as a unit among peer entities of a network. receive (RX) tracing.

system-state—Enables lldp system-state tracing.

transmit—Enables lldp PDUPower Distribution Unit or Protocol Data Unit. Power Distribution Unit is a device that distributes electric power to the networking equipment located within a data center. Protocol Data Unit contains protocol control Information that is delivered as a unit among peer entities of a network. transmit (TX) tracing.

mstp {flags|port}

Configures the MSTPMultiple Spanning Tree Protocol. MSTP configures a separate Spanning Tree for each VLAN group and blocks all but one of the possible alternate paths within each spanning tree. trace flags and trace port:

all—Enables tracing on all mstp modules

config—Enables mstp config tracing.

debug—Enables mstp debug tracing.

port-information—Enables mstp port information tracing.

received-bpdu-al—Enables mstp received bpduBridge Protocol Data Unit. A BPDU is a data message transmitted across a local area network to detect loops in network topologies. tracing.

role-selection—Enables mstp role selection tracing.

sent-bpdu-all—Enables mstp sent bpduBridge Protocol Data Unit. A BPDU is a data message transmitted across a local area network to detect loops in network topologies. tracing.

state-machine-changes—Enables mstp state machine change tracing.

system—Enables mstp system tracing.

topology-change—Enables mstp topology change tracing.

ospf flags

Configures the OSPFOpen Shortest Path First. OSPF is a link-state routing protocol for IP networks. It uses a link-state routing algorithm and falls into the group of interior routing protocols that operates within a single Autonomous System (AS). trace options:

all—Enables tracing for all ospf events.

cnf—Enables configuration events tracing.

db—Enables database operations tracing.

dd—Enables database description packets tracing.

debug—Enables internal debug tracing.

dr-elect—Enables designated routerDesignated router refers to a router interface that is elected to originate network link advertisements for networks using the OSPF protocol. election tracing.

flood—Enables linkstate flooding tracing.

hello—Enables tracing for hello packets.

lsa—Enables link state advertisement packets tracing.

lsr—Enables link state request packets tracing.

lsu—Enables link state update packets tracing.

msm—Enables msm events tracing.

pkt-all—Enables tracing for all packets.

spf—Enables SPF operations tracing.

state—Enables interface, neighbor, area changes tracing.

pim flags

Configures PIMProtocol-Independent Multicast. PIM refers to a family of multicast routing protocols for IP networks that provide one-to-many and many-to-many distribution of data over a LAN, WAN, or the Internet. sparse mode trace options:

adjacency—Enables pim sparse mode adjacency tracing.

all—Enables tracing on all pim sparse mode modules.

debug—Enables internal state tracing for pim sparse mode modules.

jp-asserts—Enables pim sparse mode join-prune/assert tracing.

register—Enables pim sparse mode register tracing.

route—Enables pim sparse mode route tracing.

state—Enables pim sparse mode state tracing.

rmon {flags|level|size}

Configures the RMONRemote Monitoring. RMON provides standard information that a network administrator can use to monitor, analyze, and troubleshoot a group of distributed LANs. trace flags:

alarm—Enables rmon alarm module debug tracing.

all—Enables rmon all module debug tracing.

cli—Enables rmon CLICommand-Line Interface. A console interface with a command line shell that allows users to execute text input as commands and convert these commands to appropriate functions. module debug tracing.

event—Enables rmon event debug tracing.

history—Enables rmon history module debug tracing.

ifstat—Enables rmon interface statistics debug tracing.

log—Enables rmon log debug tracing.

snmp—Enables rmon SNMPSimple Network Management Protocol. SNMP is a TCP/IP standard protocol for managing devices on IP networks. Devices that typically support SNMP include routers, switches, servers, workstations, printers, modem racks, and more. It is used mostly in network management systems to monitor network-attached devices for conditions that warrant administrative attention.  module debug tracing.

Configures the RMONRemote Monitoring. RMON provides standard information that a network administrator can use to monitor, analyze, and troubleshoot a group of distributed LANs. tracing levels:

alert—Alert messages

critical—Critical messages

debugging—Debug messages

emergency—Emergency messages

errors—Error messages

informational—Informational messages

notice—Notification messages

warning—Warning messages

Configures the maximum size for RMONRemote Monitoring. RMON provides standard information that a network administrator can use to monitor, analyze, and troubleshoot a group of distributed LANs. trace file in MB.

routing flags

Configures the layer3 manager trace options:

all—Enables tracing on all layer3 manager events.

arp—Enables arp module tracing.

configuration—Enables layer3 configuration processing tracing.

event—Enables layer3 manager system events tracing.

interface—Enables layer3 manager interface events tracing.

route—Enables route table updates tracing.

stack-manager {flags|level}

Configures the stack manager trace flags:

adjacency—Enables stack-manager adjacency tracing.

all—Enables tracing for all stack-manager modules.

asp—Enables aruba stacking protocol tracing.

configuration—Enables tracing for configuration of stack-manager.

primary-election—Enables tracing for primary election.

route—Enables stack-manager route calculations tracing.

system—Enables tracing for stack-manager interaction with other components.

webui—Enables tracing for stack-manager interaction with WebUI.

Configures the stack manager tracing level:

alert—Alert messages

critical—Critical messages

debugging—Debug messages

emergency—Emergency messages

errors—Error messages

informational—Informational messages

notice—Notification messages

warning—Warning messages

Example

The following command enables tracing on all IGMPInternet Group Management Protocol. Communications protocol used by hosts and adjacent routers on IP networks to establish multicast group memberships. modules:

(host) [mynode] (config) #traceoptions igmp flags all

Command History

Release

Modification

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms

Base operating system.

Config mode on Mobility Master.

/*]]>*/