You are here: Home > CLI Commands > Just_CLI_Topics > vpdn group pptp

vpdn group pptp

vpdn group pptp

client configuration {dns|wins} <ipaddr1> [<ipaddr2>]

disable|enable

no ...

ppp authentication {MSCHAP|MSCHAPv2}

pptp echo <seconds>

Description

This command configures a PPTPPoint-to-Point Tunneling Protocol. PPTP is a method for implementing virtual private networks. It uses a control channel over TCP and a GRE tunnel operating to encapsulate PPP packets. VPNVirtual Private Network. VPN enables secure access to a corporate network when located remotely. It enables a computer to send and receive data across shared or public networks as if it were directly connected to the private network, while benefiting from the functionality, security, and management policies of the private network. This is done by establishing a virtual point-to-point connection through the use of dedicated connections, encryption, or a combination of the two. connection.

Syntax

Parameter

Description

Range

Default

client configuration

Configures parameters for the remote clients.

dns

Configures a primary and optional secondary DNSDomain Name System. A DNS server functions as a phone book for the intranet and Internet users. It converts human-readable computer host names into IP addresses and IP addresses into host names. It stores several records for a domain name such as an address 'A' record, name server (NS), and mail exchanger (MX) records. The Address 'A' record is the most important record that is stored in a DNS server, because it provides the required IP address for a network peripheral or element. server.

wins

Configures a primary and optional secondary WINS server.

disable|enable

Disables or enables termination of PPTPPoint-to-Point Tunneling Protocol. PPTP is a method for implementing virtual private networks. It uses a control channel over TCP and a GRE tunnel operating to encapsulate PPP packets. clients.

enabled

no

Negates any configured parameter.

ppp authentication

Enables the protocols for PPPPoint-to-Point Protocol. PPP is a data link (layer 2) protocol used to establish a direct connection between two nodes. It can provide connection authentication, transmission encryption, and compression. authentication. This list should match the PPTPPoint-to-Point Tunneling Protocol. PPTP is a method for implementing virtual private networks. It uses a control channel over TCP and a GRE tunnel operating to encapsulate PPP packets. configuration configured with the vpn-dialer command on the managed device.

MSCHAP

Use MSCHAP with PPPPoint-to-Point Protocol. PPP is a data link (layer 2) protocol used to establish a direct connection between two nodes. It can provide connection authentication, transmission encryption, and compression. authentication.

MSCHAPv2

Use MSCHAPv2 with PPPPoint-to-Point Protocol. PPP is a data link (layer 2) protocol used to establish a direct connection between two nodes. It can provide connection authentication, transmission encryption, and compression. authentication. This is the default for L2TPLayer-2 Tunneling Protocol. L2TP is a networking protocol used by the ISPs to enable VPN operations.

pptp echo

Time, in seconds, that the managed device waits for a PPTPPoint-to-Point Tunneling Protocol. PPTP is a method for implementing virtual private networks. It uses a control channel over TCP and a GRE tunnel operating to encapsulate PPP packets. echo response from the client before considering the client to be down. The client is disconnected if it does not respond within this interval.

10-300

60 seconds

Usage Guidelines

PPTPPoint-to-Point Tunneling Protocol. PPTP is a method for implementing virtual private networks. It uses a control channel over TCP and a GRE tunnel operating to encapsulate PPP packets. connections require user-level authentication through a PPPPoint-to-Point Protocol. PPP is a data link (layer 2) protocol used to establish a direct connection between two nodes. It can provide connection authentication, transmission encryption, and compression. authentication protocol (MSHCAPv2 is the currently-supported method.) Client addresses are assigned from a pool configured with the pptp command.

Example

The following command configures virtual private dial-in networking:

vpdn group pptp

ppp authentication MSCHAPv2

client configuration dns 10.1.1.2

client configuration wins 10.1.1.2

Command History

Release

Modification

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms

Base operating system.

Config mode on Mobility Master.

/*]]>*/