Configuring the Mobility Master IPv6 Address

You can configure the Mobility Master IPv6 address used for PSK Pre-shared key. A unique shared secret that was previously shared between two parties by using a secure channel. This is used with WPA security, which requires the owner of a network to provide a passphrase to users for network access. authentication on the managed device, using the WebUI and CLI Command-Line Interface. A console interface with a command line shell that allows users to execute text input as commands and convert these commands to appropriate functions..

The initial IPv6 masteripv6 configuration on local must be done using the CLI Command-Line Interface. A console interface with a command line shell that allows users to execute text input as commands and convert these commands to appropriate functions.. Once configured, any change in masteripv6 can be done through WebUI or CLI Command-Line Interface. A console interface with a command line shell that allows users to execute text input as commands and convert these commands to appropriate functions.. This change in masteripv6 should remain in the same IP address family. Change from masteripv6 to masterip (vice-versa) requires a write erase on the managed device.

The following procedure describes how to configure the master IPv6 address for PSK Pre-shared key. A unique shared secret that was previously shared between two parties by using a secure channel. This is used with WPA security, which requires the owner of a network to provide a passphrase to users for network access. authentication.

  1. In the Managed Network node hierarchy, navigate to the Configuration > Controllers menu.
  2. Select a controller from the Controllers table.
  3. Select PSK from the Authentication drop-down list.
  4. Enter the Mobility master IPV4 address, Mobility master IPV6 address, and Passphrase.
  5. Click Submit.
  6. Click Pending Changes.
  7. In the Pending Changes window, select the check box and click Deploy changes.

The following CLI Command-Line Interface. A console interface with a command line shell that allows users to execute text input as commands and convert these commands to appropriate functions. command configures the master IPv6 address for PSK Pre-shared key. A unique shared secret that was previously shared between two parties by using a secure channel. This is used with WPA security, which requires the owner of a network to provide a passphrase to users for network access. authentication.

(host) [md] (config) #masteripv6 <masteripv6>

ipsec <key> [fqdn <local-fqdn>][interface|{vlan <id>}][masteripv4 <masteripv4>]

In a native IPv6 deployment, it is not mandatory to configure the IPv4 address of the Mobility Master or managed device, when IPv6 address is configured. Hence, the Mobility master IPV4 address field in the WebUI and the masteripv4 parameter under masteripv6 CLI Command-Line Interface. A console interface with a command line shell that allows users to execute text input as commands and convert these commands to appropriate functions. command are optional in a pure IPv6 network.

You can configure the master IPv6 address used for certificate-based authentication on the managed device.

The following procedure describes how to configure the master IPv6 address for certificate-based authentication.

  1. In the Managed Network node hierarchy, navigate to the Configuration > Controllers menu.
  2. Select a controller from the Controllers table.
  3. Select Certificate from the Authentication drop-down list.
  4. Select Custom/Factory from the Certificate type drop-down list.
  5. Enter the Mobility master IPV4 address and Mobility master IPV6 address.
  6. Click Submit.
  7. Click Pending Changes.
  8. In the Pending Changes window, select the check box and click Deploy changes.

The following CLI Command-Line Interface. A console interface with a command line shell that allows users to execute text input as commands and convert these commands to appropriate functions. command configures the master IPv6 address for certificate-based authentication:

(host) [myd] (config) #masteripv6 <masteripv6>

ipsec-custom-cert master-mac-1-c <mac-1-c> ca-cert <ca> server-cert [fqdn-v <local-fqdn-v>][interface-c {uplink-v <uplink-v> | vlan-c <id-c>] masteripv4 {fqdn-v|interface-c|masteripv4|suite-b} siute-b {fqdn-v|interface-c|masteripv4|suite-b}

ipsec-factory-cert master-mac-1 <MAC> [fqdn-c <local-fqdn-c>][interface-v {uplink-v <uplink-v> | vlan-c <id-c>] [master-mac-2 <MAC>] [masteripv4 <masteripv4>]

ArubaOS reboots the managed device when the primary IPv6 address is changed on the managed device. However, a change in the secondary IPv6 address does not require a reboot of the managed device.