ap wired-port-profile

ap wired-port-profile {default | <profile-name>}

aaa-profile {default | <profile-name>}

authentication-timeout <timeout>

auto-recovery-enable

auto-recovery-interval <auto-recovery-interval>

bridge-role

broadcast-threshold <broadcast-threshold>

clone {default | <source>}

enet-link-profile <profile-name>

lldp-profile {default | <profile-name>}

loop-detection-interval <loop-detection-interval>

loop-protect-enable

no

portfast

portfast-trunk

rap-backup

shutdown

spanning-tree

storm-control-broadcast

storm-control-broadcast-threshold

wired-ap-profile <profile-name>

Description

This command configures a wired port profile. This command is only applicable to APs with Ethernet ports. Issue this command to enable or disable the wired port, define an AAA profile for wired port devices, and associate the port with an ethernet link profile that defines its speed and duplex values.

Parameter

Description

ap wired-port-profile

<profile-name>

Name of this instance of the profile. The name must be 1–63 characters.

aaa-profile <profile-name>

Name of a AAA profile to be used by devices connecting to the wired port of the AP.

authentication-timeout

<timeout>

Authentication timeout value, in seconds, for devices connecting the wired port of the AP.

Range: 1-65535

Default: 5

auto-recovery-enable

Enables automatic recovery of the port in the AP that is shut down because of loop protection. After the automatic recovery, if the loop re-occurs, then the port is shutdown again

Disabled

auto-recovery-interval <auto-recovery-interval>

Specify the time, in seconds, to automatically recover the port in the AP that is shut down because of loop protection.

Range: 30-43200

Default: 300

bridge-role <role>

Role that is assigned to a user if split-tunnel authentication fails.

broadcast-threshold <broadcast-threshold>

Set the storm control threshold in packets per second.

Range: 1-1000000

Default: 2000

clone <source>

Create a new AP wired port profile based upon the values of an existing profile.

enet-link-profile

<profile-name>

Specify an Ethernet link profile to be used by devices associated with this wired port profile. The Ethernet link profile defines the duplex value and speed to be used by the port.

lldp-profile <profile-name>

Specify an LLDP profile to be used by devices associated with this wired port profile. The LLDP profile specifies the type-length-value (TLV) elements to be sent in LLDP PDUs.

loop-detection-interval <loop-detection-interval>

Specify the time, in seconds, to send loop detection packets on the ports of an AP.

Range: 1-10

Default: 2

loop-protect-enable

Enables loop protection on the ports of an AP.

Default: Disabled

no

Negates any defined parameter

portfast

Enables portfast for AP wired ports.

Spanning tree must be enabled before this command can be used.

portfast-trunk

Spanning tree must be enabled before this command can be used.

rap-backup

Use the rap-backup parameter to use the wired port on a Remote AP for local connectivity and troubleshooting when the AP cannot reach the managed device. If the AP is not connected to the managed device, no firewall policies will be applied when this option is enabled. (The AAA profile will be applied when the AP is connected to managed device).

shutdown

Disable the wired AP port.

spanning-tree

Enables the spanning-tree protocol.

storm-control-broadcast

Enables the broadcast storm control. When this parameter is enabled, if the AP detects a loop on one of its Ethernet port, it shuts down the Ethernet port. This prevents the AP from receiving or sending any frames.

storm-control-broadcast-threshold

Specify the broadcast packets per second on each Ethernet port of an AP before the Ethernet port is shut down.

Default: 2000

wired-ap-profile <profile-name>

Name of a wired AP profile to be used by devices connecting the wired port of the AP. The wired AP profile defines the forwarding mode and switchport values used by the port.

Example

The following command defines a AAA profile for wired port devices:

(host)[mynode] (config) #ap wired-port-profile wiredport1

(host)[mynode] (AP wired port profile"wiredport1") #aaa-profile default-open

(host)[mynode] (AP wired port profile"wiredport1") #authentication-timeout 30

(host)[mynode] (AP wired port profile"wiredport1") #wired-ap-profile wiredap1

Command History

Release

Modification

ArubaOS 8.3.0.0

The following parameters were introduced:

auto-recovery-enable

auto-recovery-interval

loop-detection-interval

loop-protect-enable

storm-control-broadcast

storm-control-broadcast-threshold

ArubaOS 8.0.0.0

Command introduced.

Command Information

Platforms

License

Command Mode

All platforms

Base operating system, except for noted parameters.

Config mode on Mobility Conductor.